IEC 60728-6:2011(E) lays down the measuring methods, performance requirements and data publication requirements of optical equipment of cable networks for television signals, sound signals and interactive services. This third edition cancels and replaces the second edition published in 2003 of which it constitutes a technical revision. It includes the following significant technical changes with respect to the previous edition: - The normative references were updated. - The methods of measurement for optical power and return loss were substituted by references to other standards. - The method of measurement for polarization dependent loss was deleted. - A method of measurement for carrier-to-crosstalk ratio (CCR) was added. - The methods of measurement for CSO and CTB of optical amplifiers were substituted by a method of measurement for microscopic gain tilt of optical amplifiers. This parameter can be used for calculating the second order distortion of optical amplifiers according to the method described in the new Annex B. New classes for optical transmitters and receivers have been defined.
Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.
EN 60068-1:1994 Environmental testing - Part 1: General and guidance
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 60068-1:1994 Environmental testing - Part 1: General and guidance
EN 60068-2-14:2009 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
EN 60068-2-27:2009 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
EN 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
EN 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
EN 60068-2-31:2008 Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens
EN 60068-2-40:1999 Environmental testing - Part 2: Tests - Test Z/AM: Combined cold/low air pressure tests
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
EN 60169-24:1993 Radio-frequency connectors - Part 24: Radio-frequency coaxial connectors with screw coupling, typically for use in 75 ohm cable distribution systems (Type F)
EN 60728-11:2010 Cable networks for television signals, sound signals and interactive services - Part 11: Safety
EN 60728-13:2010 Cable networks for television signals, sound signals and interactive services - Part 13: Optical systems for broadcast signal transmissions
EN 60728-1:2014 Cable networks for television signals, sound signals and interactive services - Part 1: System performance of forward paths
EN 60728-3:2011 Cable networks for television signals, sound signals and interactive services - Part 3: Active wideband equipment for cable networks
EN 60793-2-50:2008 Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres
EN 60825-1:1994 Safety of laser products - Part 1: Equipment classification, requirements and user's guide
EN 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
EN 61280-1-1:2013 Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable
EN 61280-1-3:2010 Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Central wavelength and spectral width measurement
EN 61290-1-1:1998 Optical fibre amplifiers - Basic specification - Part 1-1: Test methods for gain parameters - Optical spectrum analyzer
EN 61290-1-1:2006 Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
EN 61290-1-1:2015 Optical amplifiers - Test methods - Part 1-1: Power and gain parameters - Optical spectrum analyzer method
EN 61290-1-2:1998 Optical fibre amplifiers - Basic specification - Part 1-2: Test methods for gain parameters - Electrical spectrum analyzer
EN 61290-1-2:2005 Optical amplifiers - Test methods - Part 1-2: Power and gain parameters - Electrical spectrum analyzer method
EN 61290-1-3:2015 Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
EN 61290-11-1:2008 Optical amplifiers - Test methods - Part 11-1: Polarization mode dispersion parameter - Jones matrix eigenanalysis (JME)
EN 61290-11-2:2005 Optical amplifiers - Test methods - Part 11-2: Polarization mode dispersion parameter - Poincaré sphere analysis method
EN 61290-3-2:2003 Optical amplifiers - Part 3-2: Test methods for noise figure parameters - Electrical spectrum analyzer method
EN 61290-5-1:2006 Optical amplifiers - Test methods - Part 5-1: Reflectance parameters - Optical spectrum analyzer method
EN 61290-5-2:2004 Optical amplifiers - Test methods - Part 5-2: Reflectance parameters - Electrical spectrum analyser method
EN 61290-5-3:2002 Optical fibre amplifiers - Basic specification - Part 5-3: Test methods for reflectance parameters - Reflectance tolerance using an electrical spectrum analyser
EN 61290-6-1:1998 Optical fibre amplifiers - Basic specification - Part 6-1: Test methods for pump leakage parameters - Optical demultiplexer
EN 61291-5-2:2017 Optical amplifiers - Part 5-2: Qualification specifications - Reliability qualification for optical fibre amplifiers
EN 61300-3-6:2009 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-6: Examinations and measurements - Return loss
EN 61754-4:2013 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 4: Type SC connector family
EN 80416-1:2009 Basic principles for graphical symbols for use on equipment - Part 1: Creation of graphical symbols for registration
EN 80416-2:2001 Basic principles for graphical symbols for use on equipment - Part 2: Form and use of arrows
EN 80416-3:2002 Basic principles for graphical symbols for use on equipment - Part 3: Guidelines for the application of graphical symbols
EN 80416-3:2002/A1:2011 Basic principles for graphical symbols for use on equipment - Part 3: Guidelines for the application of graphical symbols
EN IEC 60068-2-14:2023 Environmental testing - Part 2-14: Tests - Test N: Change of temperature
EN IEC 61280-1-3:2021 Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Measurement of central wavelength, spectral width and additional spectral characteristics
EN IEC 61290-1-3:2021 Optical amplifiers - Test methods - Part 1-3: Power and gain parameters - Optical power meter method
EN IEC 61291-1:2018 Optical amplifiers - Part 1: Generic specification
EN IEC 61754-4:2022 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 4: Type SC connector family
IEC 60417-DB
IEC 60529:2001
IEC 60728-2:2002 Cabled distribution systems for television and sound signals - Part 2: Electromagnetic compatibility for equipment
IEC/TR 61282-4:2003 Fibre optic communication system design guides - Part 4: Accommodation and utilization of non-linear effects
IEC/TR 61931:1998 Fibre optic - Terminology