IEC 61215-2:2021 is available as IEC 61215-2:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61215-2:2021 lays down requirements for the design qualification of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This document is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. The objective of this test sequence is to determine the electrical characteristics of the module and to show, as far as possible within reasonable constraints of cost and time, that the module is capable of withstanding prolonged exposure outdoors. This second edition of IEC 61215-2 cancels and replaces the first edition of IEC 61215-2 issued in 2016. This edition includes the following significant technical changes with respect to the previous edition: a. Addition of cyclic (dynamic) mechanical load testing (MQT 20). b. Addition of a test for detection of potential-induced degradation (MQT 21). c. Addition of test methods required for bifacial PV modules. d. Addition of test methods required for flexible modules. This includes the addition of the bending test (MQT 22). e. Revision of simulator requirements to ensure uncertainty is both well-defined and minimized. f. Correction to the hot spot endurance test, where the procedure for monolithically integrated (MLI) thin film technologies (MQT 09.2) previously included two sections describing a procedure only appropriate for silicon modules. g. Selection of three diodes, rather than all, for testing in the bypass diode thermal test (MQT 18). h. Removal of the nominal module operating test (NMOT), and associated test of performance at NMOT, from the IEC 61215 series.
IEC TR 60904–14 Photovoltaic devices – Part 14: Guidelines for production line measurements of single-junction PV module maximum power output and reporting at standard test conditions
IEC TS 60904–1–2 Photovoltaic devices – Part 1-2: Measurement of current-voltage characteristics of bifacial photovoltaic (PV) devices
IEC TS 61836 Solar photovoltaic energy systems – Terms, definitions and symbols
IEC TR 60904–14 Photovoltaic devices – Part 14: Guidelines for production line measurements of single-junction PV module maximum power output and reporting at standard test conditions
IEC TS 60904–1–2 Photovoltaic devices – Part 1-2: Measurement of current-voltage characteristics of bifacial photovoltaic (PV) devices
IEC TS 61836 Solar photovoltaic energy systems – Terms, definitions and symbols
IEC TS 62782 Photovoltaic (PV) modules – Cyclic (dynamic) mechanical load testing
IEC TS 62804–1:2015 Photovoltaic (PV) modules – Test methods for the detection of potential-induced degradation – Part 1: Crystalline silicon
IEC TS 63163:
IEC 60068–1 Environmental testing – Part 1: General and guidance
IEC 60068–2–21 Environmental testing – Part 2-21: Tests – Test U: Robustness of terminations and integral mounting devices
IEC 60068–2–78:2012 Environmental testing – Part 2-78: Tests – Test Cab: Damp heat, steady state
IEC 60891 Photovoltaic devices – Procedures for temperature and irradiance corrections to measured I-V characteristics
IEC 60904–1 Photovoltaic devices – Part 1: Measurements of photovoltaic current-voltage characteristics
IEC 60904–10 Photovoltaic devices – Part 10: Methods of linearity measurement
IEC 60904–1–1 Photovoltaic devices – Part 1-1: Measurement of current-voltage characteristics of multi-junction photovoltaic (PV) devices
IEC 60904–2 Photovoltaic devices – Part 2: Requirements for photovoltaic reference devices
IEC 60904–3 Photovoltaic devices – Part 3: Measurement principles for terrestrial photovoltaic (PV) solar devices with reference spectral irradiance data
IEC 60904–7 Photovoltaic devices – Part 7: Computation of the spectral mismatch correction for measurements of photovoltaic devices
IEC 60904–8 Photovoltaic devices – Part 8: Measurement of spectral responsivity of a photovoltaic (PV) device
IEC 60904–9:2020 Photovoltaic devices – Part 9: Classification of solar simulator characteristics
IEC 61140 Protection against electric shock – Common aspects for installation and equipment
IEC 61215–1:2021 Terrestrial photovoltaic (PV) modules – Design qualification and type approval – Part 1: Test requirements
IEC 61215–1–1 Terrestrial photovoltaic (PV) modules – Design qualification and type approval – Part 1-1: Special requirements for testing of crystalline silicon photovoltaic (PV) modules
IEC 61730–1:2016 Photovoltaic (PV) module safety qualification – Part 1: Requirements for construction
IEC 61730–2 Photovoltaic (PV) module safety qualification – Part 2: Requirements for testing
IEC 62790 Junction boxes for photovoltaic modules – Safety requirements and tests