Tässä eurooppalaisessa standardissa määritellään kantavissa puurakenteissa käytettävien puikkoliittimien materiaalia, mittoja, lujuutta, jäykkyyttä sekä pitkäaikaiskestävyyttä (kuten korroosiosuojausta) koskevat vaatimukset ja testausmenetelmät. Tämä eurooppalainen standardi koskee vain teräksestä valmistettuja puikkoliittimiä. Tässä standardissa puurakenteissa käytettävillä puikkoliittimillä tarkoitetaan nauloja, hakasia, ruuveja, tappivaarnoja sekä muttereilla kiinnitettäviä pultteja. Näiden määritelmät esitetään kohdassa 3. Tässä eurooppalaisessa standardissa määritellään myös vaatimustenmukaisuuden arviointimenettelyt ja esitetään tuotteiden merkintää koskevat vaatimukset. Tämä eurooppalainen standardi ei koske liittimiä, joita on käsitelty palokäyttäytymistä parantavilla palonestoaineilla. Tämä eurooppalainen standardi koskee myös liittimiä, jotka on pinnoitettu seuraavia tarkoituksia varten: 1 korroosiosuojaukseen (esim. kuumasinkitys, epoksipinnoitus) 2 voiteluaineena (helpottaa paikalleen asennusta) 3 ulosvetolujuuden parantamiseksi ja/tai liittimien liimaus (liimapinnoitteet).
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
Sisällysluettelo
Kansallinen esipuhe
Esipuhe (CEN)
1 Soveltamisala
2 Velvoittavat viittaukset
3 Termit ja määritelmät
4 Tunnukset ja lyhenteet
5 Mitat ja toleranssit
5.1 Mittausmenetelmä ja tarkkuus
5.2 Pituus
5.3 Nimellishalkaisija
5.4 Muut mitat
5.5 Poikkipinta-ala
6 Vaatimukset
6.1 Naulat
6.2 Hakaset
6.3 Ruuvit
6.4 Tappivaarnat
6.5 Pultit ja mutterit
7 Vaatimustenmukaisuuden arviointi
7.1 Yleistä
7.2 Alkutestaus
7.3 Tehtaan sisäinen laadunvalvonta (FPC)
8 Merkintä
8.1 Yleistä
8.2 Naulat
8.3 Hakaset
8.4 Ruuvit
8.5 Tappivaarnat
8.6 Pultit ja mutterit
Liite A Korroosiosuojausspesifikaatioiden esittäminen (velvoittava)
Liite ZA Tämän eurooppalaisen standardin kohdat, jotka liittyvät EU:n rakennustuotedirektiiviin (opastava)
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-4:2009 Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes
EN 10088-5:2009 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes
EN 10149-1:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
EN 10218-1:2012 Steel wire and wire products - General - Part 1: Test methods
EN 10263-1:2017 Steel rod, bars and wire for cold heading and cold extrusion - Part 1: General technical delivery conditions
EN 10263-2:2017 Steel rod, bars and wire for cold heading and cold extrusion - Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working
EN 10263-3:2017 Steel rod, bars and wire for cold heading and cold extrusion - Part 3: Technical delivery conditions for case hardening steels
EN 10263-4:2017 Steel rod, bars and wire for cold heading and cold extrusion - Part 4: Technical delivery conditions for steels for quenching and tempering
EN 10263-5:2017 Steel rod, bars and wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels
EN 10269:2013 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 10277:2018 Bright steel products - Technical delivery conditions
EN 1382:2016 Timber Structures - Test methods - Withdrawal capacity of timber fasteners
EN 1383:1999 Timber structures - Test methods - Pull through resistance of timber fasteners
EN 14358:2016 Timber structures - Calculation and verification of characteristic values
EN 15737:2009 Timber Structures - Test methods - Torsional resistance of driving in screws
EN 1995-1-1:2004 Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings
EN 409:2009 Timber structures - Test methods - Determination of the yield moment of dowel type fasteners
EN ISO 10666:1999 Drilling screws with tapping screw thread - Mechanical and functional properties (ISO 10666:1999)
EN ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
EN ISO 16120-1:2017 Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1:2017)
EN ISO 16120-2:2017 Non-alloy steel wire rod for conversion to wire - Part 2: Specific requirements for general purpose wire rod (ISO 16120-2:2017)
EN ISO 16120-3:2011 Non-alloy steel wire rod for conversion to wire - Part 3: Specific requirements for rimmed and rimmed substitute, low-carbon steel wire rod (ISO 16120-3:2011)
EN ISO 16120-4:2017 Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4:2017)
EN ISO 4014:2011 Hexagon head bolts - Product grades A and B (ISO 4014:2011)
EN ISO 4016:2011 Hexagon head bolts - Product grade C (ISO 4016:2011)
EN ISO 4017:2014 Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2014)
EN ISO 4018:2011 Hexagon head screws - Product grade C (ISO 4018:2011)
EN ISO 4032:2012 Hexagon regular nuts (style 1) - Product grades A and B (ISO 4032:2012)
EN ISO 4034:2012 Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)
EN ISO 683-1:2018 Heat-treatable steels, alloy steels and free-cutting steels - Part 1: Non-alloy steels for quenching and tempering (ISO 683-1:2016)
EN ISO 683-2:2018 Heat-treatable steels, alloy steels and free-cutting steels - Part 2: Alloy steels for quenching and tempering (ISO 683-2:2016)
EN ISO 6892-1:2019 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2019)
EN ISO 780:2015 Packaging - Distribution packaging - Graphical symbols for handling and storage of packages (ISO 780:2015)
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 2081:2008 Metallic and other inorganic coatings -- Electroplated coatings of zinc with supplementary treatments on iron or steel