Verkkokauppa
SFS-EN 1996-2:en
Eurocode 6. Design of masonry structures. Part 2: Design considerations, selection of materials and execution of masonry
Soveltamisala
Suomenkielistä soveltamisalaa ei ole saatavissa.
(1)P The scope of Eurocode 6 for Masonry Structures as given in 1.1.1 of EN 1996-1-1 applies also to this Part 2.
(2)P Part 2 of Eurocode 6 gives basic rules for the selection of materials and execution of masonry to enable it to comply with the design assumptions of the other parts of Eurocode 6. With the exception of the items given in 1.1(3)P, the scope of Part 2 deals with ordinary aspects of masonry design and execution including:
the selection of masonry materials;
factors affecting the performance and durability of masonry;
resistance of buildings to moisture penetration;
storage, preparation and use of materials on site;
the execution of masonry;
masonry protection during execution;
NOTE 1. Where general guidance only is given, additional guidance based on local conditions and practice may be made available in non contradictory complementary documents which may be referred to in the National Annex.
NOTE 2. The scope of Eurocode 6 excludes seismic, thermal and acoustic functional performance of masonry structures;
(3)P Part 2 of Eurocode 6 does not cover the following items:
those aspects of masonry covered in other parts of Eurocode 6;
aesthetic aspects;
applied finishes;
health & safety of persons engaged in the design or execution of masonry;
the environmental effects of masonry buildings, civil engineering works and structures on their surroundings.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
(1)P The scope of Eurocode 6 for Masonry Structures as given in 1.1.1 of EN 1996-1-1 applies also to this Part 2.
(2)P Part 2 of Eurocode 6 gives basic rules for the selection of materials and execution of masonry to enable it to comply with the design assumptions of the other parts of Eurocode 6. With the exception of the items given in 1.1(3)P, the scope of Part 2 deals with ordinary aspects of masonry design and execution including:
the selection of masonry materials;
factors affecting the performance and durability of masonry;
resistance of buildings to moisture penetration;
storage, preparation and use of materials on site;
the execution of masonry;
masonry protection during execution;
NOTE 1. Where general guidance only is given, additional guidance based on local conditions and practice may be made available in non contradictory complementary documents which may be referred to in the National Annex.
NOTE 2. The scope of Eurocode 6 excludes seismic, thermal and acoustic functional performance of masonry structures;
(3)P Part 2 of Eurocode 6 does not cover the following items:
those aspects of masonry covered in other parts of Eurocode 6;
aesthetic aspects;
applied finishes;
health & safety of persons engaged in the design or execution of masonry;
the environmental effects of masonry buildings, civil engineering works and structures on their surroundings.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
Tuoteryhmä(t)
Sidokset
Velvoittavat viittaukset
EN 1015-11:2019 Methods of test for mortar for masonry - Part 11: Determination of flexural and compressive strength of hardened mortar
EN 1015-17:2000 Methods of test for mortar for masonry - Part 17: Determination of water-soluble chloride content of fresh mortars
EN 1052-1:1998 Methods of test for masonry - Part 1: Determination of compressive strength
EN 1015-17:2000 Methods of test for mortar for masonry - Part 17: Determination of water-soluble chloride content of fresh mortars
EN 1052-1:1998 Methods of test for masonry - Part 1: Determination of compressive strength
Tekninen komitea
Direktiivi
Vahvistuspäivä
13.02.2006
Julkaisupäivä
03.03.2006
Painos
1
Sivumäärä
35
Julkaisun kieli
englanti
Lisätiedot
Lisätietoja eurokoodeista www.eurocodes.fi.