This European Standard specifies requirements relating to the design, manufacture, construction, safety and performance (efficiency and emissions), instructions and marking together with associated test methods and test fuels for type-testing residential space heaters fired by wood pellets, and mechanically fed up to 50 kW nominal heat output. These appliances may be freestanding or inset appliances and provide heat into the space where they are installed and may be operated with either natural draught or fan-assisted combustion air. Additionally, where fitted with a boiler, they also provide domestic hot water and/or central heating. These appliances burn wood pellets only, in accordance with the appliance manufacturer's instructions. They operate with firedoors closed only. Non mechanically fed appliances burning solid mineral fuels, peat briquettes and natural or manufactured wood logs are not included in this European Standard, but are covered by EN 13229 and EN 13240. NOTE These appliances may have an integral fuel hopper or be combined with an external fuel hopper.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
CEN/TS 14774-1:2004 Solid biofuels - Methods for determination of moisture content - Oven dry method - Part 1: Total moisture - Reference method
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
CEN/TS 14774-1:2004 Solid biofuels - Methods for determination of moisture content - Oven dry method - Part 1: Total moisture - Reference method
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10025-4:2019 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019+A1 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-4:2019+A1:2022 Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
EN 10025-5:2019 Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
EN 10025-6:2019 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10025-6:2019+A1 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10025-6:2019+A1:2022 Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
EN 10027-2:1992 Designation systems for steels - Part 2: Numerical system
EN 10028-2:2003 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10028-3:1992 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
EN 10088-2:2005 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10111:2008 Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
EN 10120:1996 Steel sheet and strip for welded gas cylinders
EN 10226-3:2005 Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges
EN 1561:1997 Founding - Grey cast irons
EN 1563:1997 Founding - Spheroidal graphite cast irons
EN 50165:1997 Electrical equipment of non-electric appliances for household and similar purposes - Safety requirements
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 228-2:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987)
ISO 1171:1997 Solid mineral fuels -- Determination of ash
ISO 1928:1995 Solid mineral fuels -- Determination of gross calorific value by the bomb calorimetric method, and calculation of net calorific value
ISO 2859-0:1995 Sampling procedures for inspection by attributes -- Part 0: Introduction to the ISO 2859 attribute sampling system
ISO 2859-1:1999 Sampling procedures for inspection by attributes -- Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
ISO 2859-1:1999/Cor 1:2001
ISO 2859-2:1985 Sampling procedures for inspection by attributes -- Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
ISO 2859-3:2005 Sampling procedures for inspection by attributes -- Part 3: Skip-lot sampling procedures
ISO 2859-4:2002 Sampling procedures for inspection by attributes -- Part 4: Procedures for assessment of declared quality levels
ISO 2859-5:2005 Sampling procedures for inspection by attributes -- Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
ISO 334:1992 Solid mineral fuels -- Determination of total sulfur -- Eschka method
ISO 351:1996 Solid mineral fuels -- Determination of total sulfur -- High temperature combustion method
ISO 501:2003 Hard coal -- Determination of the crucible swelling number
ISO 562:1998 Hard coal and coke -- Determination of volatile matter
ISO 609:1996 Solid mineral fuels -- Determination of carbon and hydrogen -- High temperature combustion method
ISO 687:2004 Solid mineral fuels -- Coke -- Determination of moisture in the general analysis test sample
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads -- Part 1: Dimensions, tolerances and designation