This European Standard specifies requirements for prefabricated lintels for maximum spans of 4,5 m and made from steel, autoclaved aerated concrete, manufactured stone, concrete, fired clay units, calcium silicate units, natural stone units, or a combination of these materials. Concrete and steel beams conforming to EN 1090-1, EN 12602 and EN 13225, as appropriate, are not covered by this standard. Prefabricated lintels can be either complete lintels or the prefabricated part of a composite lintel. This European Standard is not applicable to: a) lintels completely made on site; b) lintels of which the tensile parts are made on site; c) timber lintels; d) natural stone lintels, not reinforced. Linear components spanning clear openings greater than 4,5 m in masonry walls and linear components intended for use independently in a structural role (e.g. beams) are not covered by this standard.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
EN 10080:2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-1:2023 Stainless steels - Part 1: List of stainless steels
EN 10080:2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-1:2023 Stainless steels - Part 1: List of stainless steels
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-3:2023 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resistant steels for general purposes
EN 10088-4:2009 Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes
EN 10088-5:2009 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes
EN 10346:2009 Continuously hot-dip coated steel flat products - Technical delivery conditions
EN 12602:2008 Prefabricated reinforced components of autoclaved aerated concrete
EN 13501-2:2016 Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services
EN 13501-2:2023 Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance and/or smoke control tests, excluding ventilation services
EN 1745:2020 Masonry and masonry products - Methods for determining thermal properties
EN 206-1:2000 Concrete - Part 1: Specification, performance, production and conformity
EN 771-1:2011+A1:2015 Specification for masonry units - Part 1: Clay masonry units
EN 771-2:2011+A1:2015 Specification for masonry units - Part 2: Calcium silicate masonry units
EN 771-3:2011+A1:2015 Specification for masonry units - Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)
EN 771-4:2011+A1:2015 Specification for masonry units - Part 4: Autoclaved aerated concrete masonry units
EN 771-5:2011+A1:2015 Specification for masonry units - Part 5: Manufactured stone masonry units
EN 771-6:2011+A1:2015 Specification for masonry units - Part 6: Natural stone masonry units
EN 772-11:2011 Methods of test for masonry units - Part 11: Determination of water absorption of aggregate concrete, autoclaved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units
EN 772-1:2011+A1:2015 Methods of test for masonry units - Part 1: Determination of compressive strength
EN 846-11:2000 Methods of test for ancillary components for masonry - Part 11: Determination of dimensions and bow of lintels
EN 846-13:2001 Methods of test for ancillary components for masonry - Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings
EN 846-14:2012 Methods of test for ancillary components for masonry - Part 14: Determination of the initial shear strength between the prefabricated part of a composite lintel and the masonry above it
EN 846-9:2016 Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels
EN 990:2002 Test methods for verification of corrosion protection of reinforcement in autoclaved aerated concrete and lightweight aggregate concrete with open structure
EN 998-2:2010 Specification for mortar for masonry - Part 2: Masonry mortar
EN ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
EN ISO 1461:2022 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2022)
EN ISO 1463:2004 Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2003)
EN ISO 1463:2021 Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2021)
FprEN 10138-1 Prestressing steels - Part 1: General requirements
FprEN 10138-2 Prestressing steels - Part 2: Wire
FprEN 10138-3 Prestressing steels - Part 3: Strand
FprEN 10138-4 Prestressing steels - Part 4: Bar