Small craft. Stability and buoyancy assessment and categorization. Part 1: Non-sailing boats of hull length greater than or equal to 6 m (ISO 12217-1:2015)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 12217-1:2015 specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed. The evaluation of stability and buoyancy properties using this part of ISO 12217 will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum total load. ISO 12217-1:2015 is principally applicable to boats propelled by human or mechanical power of 6 m up to 24 m hull length. However, it can also be applied to boats of under 6 m if they do not attain the desired design category specified in ISO 12217-3 and they are decked and have quick-draining recesses which comply with ISO 11812. In relation to habitable multihulls, ISO 12217-1:2015 includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation. ISO 12217-1:2015 excludes: inflatable and rigid-inflatable boats covered by ISO 6185, except for references made in ISO 6185 to specific clauses of ISO 12217; personal watercraft covered by ISO 13590 and other similar powered craft; gondolas and pedalos; sailing surfboards; surfboards, including powered surfboards; hydrofoils and hovercraft when not operating in the displacement mode; and submersibles. ISO 12217-1:2015 does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 Primary
3.2 Downflooding
3.3 Dimensions, areas and angles
3.4 Condition, mass and volume
3.5 Other terms and definitions
4 Symbols
5 Procedure
5.1 Maximum load
5.2 Sailing or non-sailing
5.3 Tests and calculations to be applied
5.4 Variation in input parameters
6 Tests, calculations and requirements
6.1 Downflooding
6.2 Offset-load test
6.3 Resistance to waves and wind
6.4 Heel due to wind action
6.5 Recess size
6.6 Habitable multihull boats
6.7 Motor sailers
6.8 Flotation requirements
6.9 Detection and removal of water
7 Application
7.1 Deciding the design category
7.2 Meaning of the design categories
Annex A Full method for required downflooding height (normative)
Annex B Method for offset-load test (normative)
Annex C Methods for calculating downflooding angle (normative)
Annex D Method for measuring freeboard margin (normative)
Annex E Determining the curve of righting moments (normative)
Annex F Method for level flotation test (normative)
Annex G Flotation material and elements (normative)
Annex H Information for owner's manual (normative)
Annex I Summary of requirements (informative)
Annex J Worksheets (informative)
Annex K Illustration of recess retention level (informative)
ISO 10240:2004 Small craft -- Owner's manual
ISO 11812:2001 Small craft -- Watertight cockpits and quick-draining cockpits
ISO 12216:2002 Small craft -- Windows, portlights, hatches, deadlights and doors -- Strength and watertightness requirements
ISO 10240:2004 Small craft -- Owner's manual
ISO 11812:2001 Small craft -- Watertight cockpits and quick-draining cockpits
ISO 12216:2002 Small craft -- Windows, portlights, hatches, deadlights and doors -- Strength and watertightness requirements
ISO 12217-2:2015 Small craft -- Stability and buoyancy assessment and categorization -- Part 2: Sailing boats of hull length greater than or equal to 6 m
ISO 12217-3:2015 Small craft -- Stability and buoyancy assessment and categorization -- Part 3: Boats of hull length less than 6 m
ISO 14946:2001 Small craft -- Maximum load capacity
ISO 15083:2003 Small craft - Bilge-pumping systems
ISO 15085:2003 Small craft -- Man-overboard prevention and recovery
ISO 2896:2001 Rigid cellular plastics -- Determination of water absorption
ISO 3864-1:2011 Graphical symbols -- Safety colours and safety signs -- Part 1: Design principles for safety signs and safety markings
ISO 6185-4:2011 Inflatable boats -- Part 4: Boats with a hull length of between 8 m and 24 m with a motor power rating of 15 kW and greater
ISO 8666:2016 Small craft -- Principal data
ISO 9093-1:1994 Small craft -- Seacocks and through-hull fittings -- Part 1: Metallic
ISO 9093-2:2002 Small craft -- Seacocks and through-hull fittings -- Part 2: Non-metallic