This European Standard specifies requirements relating to the design, manufacture, construction, safety and performance (efficiency and emission) instructions and marking together with associated test methods and test fuels for type testing residential roomheaters fired by solid fuel.
This Standard is applicable to non-mechanically fired appliances which are listed under categories 1a and 2a of Table 1. These appliances provide heat into the space where they are installed. Additionally, where fitted with a boiler, they also provide domestic hot water and/or central heating. These appliances may burn either solid mineral fuels, peat briquettes, natural or manufactured wood logs or be multi-fuel in accordance with the appliance manufacturer's instructions.
This standard is not applicable to appliances with fan assisted combustion air.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
EN 10027-2:1992 Designation systems for steels - Part 2: Numerical system
EN 10028-2:1992 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10029:1991 Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and mass
EN 10027-2:1992 Designation systems for steels - Part 2: Numerical system
EN 10028-2:1992 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10029:1991 Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and mass
EN 10088-2:1995 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip for general purposes
EN 10111:1998 Continuously hot-rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
EN 10120:1996 Steel sheet and strip for welded gas cylinders
EN 1561:1997 Founding - Grey cast irons
EN 1563:1997 Founding - Spheroidal graphite cast irons
EN 60335-2-102:2016 Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
ISO 1171:1997 Solid mineral fuels -- Determination of ash
ISO 1928:1995 Solid mineral fuels -- Determination of gross calorific value by the bomb calorimetric method, and calculation of net calorific value
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 228-2:1987 Pipe threads where pressure-tight joints are not made on the threads -- Part 2: Verification by means of limit gauges
ISO 2859-1:1999 Sampling procedures for inspection by attributes -- Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
ISO 2859-2:1985 Sampling procedures for inspection by attributes -- Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
ISO 2859-3:2005 Sampling procedures for inspection by attributes -- Part 3: Skip-lot sampling procedures
ISO 2859-4:2002 Sampling procedures for inspection by attributes -- Part 4: Procedures for assessment of declared quality levels
ISO 2859-5:2005 Sampling procedures for inspection by attributes -- Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection
ISO 331:1983 Coal -- Determination of moisture in the analysis sample -- Direct gravimetric method
ISO 334:1992 Solid mineral fuels -- Determination of total sulfur -- Eschka method
ISO 351:1996 Solid mineral fuels -- Determination of total sulfur -- High temperature combustion method
ISO 501:1981 Coal -- Determination of the crucible swelling number
ISO 562:1998 Hard coal and coke -- Determination of volatile matter
ISO 609:1996 Solid mineral fuels -- Determination of carbon and hydrogen -- High temperature combustion method
ISO 687:1974 Coke -- Determination of moisture in the analysis sample
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 7-2:2000 Pipe threads where pressure-tight joints are made on the threads -- Part 2: Verification by means of limit gauges