Earth-moving and building construction machinery. Electromagnetic compatibility (EMC) of machines with internal electrical power supply. Part 1: General EMC requirements under typical electromagnetic environmental conditions (ISO 13766-1:2018)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 13766-1:2018 provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility (EMC) of earth-moving machinery, as defined in ISO 6165:2012, and of the following building construction machinery as defined in ISO/TR 12603:2010: - drilling and foundation equipment; - equipment used for the preparation, conveyance and compaction of concrete, mortar and processing reinforcement; - road construction and maintenance machinery and equipment. ISO 13766-1:2018 deals with general EMC requirements under typical electromagnetic environmental conditions. (ISO 13766-2:2018 deals with EMC requirements specifically related to functional safety). Electrical/electronic subassemblies (ESA) and separate ESA intended to be fitted to the machinery are also dealt with. The following electromagnetic disturbance phenomena are evaluated: - broadband and narrowband electromagnetic interference; - electromagnetic field immunity; - electrostatic discharge; - conducted transients. The machinery can have DC or AC or a combination of both as the internal electrical power supply system. ISO 13766-1:2018 is not applicable to machines that are designed to be supplied by an external mains network or to phenomena caused by military applications. NOTE 1 Grid-connected machines are covered by IEC 61000. NOTE 2 Hybrid machines are covered in UN ECE R10-Rev. 5.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
4.1 General requirements
4.2 Specifications for broadband electromagnetic emission radiated from machinery
4.3 Specifications concerning narrowband electromagnetic emission radiated from machinery
4.4 Specifications concerning the immunity of machinery to electromagnetic radiation
4.5 Specifications concerning broadband electromagnetic emissions radiated from ESA
4.6 Specifications concerning narrowband electromagnetic emissions radiated from ESA
4.7 Specifications concerning the immunity of ESA to electromagnetic radiation
4.8 Electrostatic discharge (ESD)
4.9 Conducted transients
5 Exceptions
6 Test report
Annex A Reference limits (normative)
Annex B Method of measurement of radiated broadband electromagnetic emissions from machinery — Complete machine only (normative)
Annex C Method of measurement of radiated narrowband electromagnetic emissions from machinery — Complete machine only (normative)
Annex D Method of measurement of radiated broadband electromagnetic emissions from electrical/electronic sub-assemblies (ESA) (normative)
Annex E Method of measurement of radiated narrowband electromagnetic emissions from ESA (normative)
Annex F Guidance for selecting test specimen configuration and additional considerations (informative)
CISPR 12 AMD 1:2009
CISPR 12:2007
CISPR 16-1-1 Edition 3.2:2014
CISPR 16-1-4 Edition 3.1:2012
CISPR 25:2008
ISO 10605:2008 Road vehicles -- Test methods for electrical disturbances from electrostatic discharge
ISO 11451-1:2015 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 1: General principles and terminology
ISO 11451-2:2015 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 2: Off-vehicle radiation sources
ISO 11451-4:2013 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 4: Bulk current injection (BCI)
ISO 11452-1:2015 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 1: General principles and terminology
ISO 11452-2:2004 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 2: Absorber-lined shielded enclosure
ISO 11452-3:2016 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 3: Transverse electromagnetic (TEM) cell
ISO 11452-4:2011 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 4: Harness excitation methods
ISO 11452-5:2002 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 5: Stripline
ISO 12100:2010 Safety of machinery -- General principles for design -- Risk assessment and risk reduction
ISO 16750-1:2006 Road vehicles -- Environmental conditions and testing for electrical and electronic equipment -- Part 1: General
ISO 16750-2:2012 Road vehicles -- Environmental conditions and testing for electrical and electronic equipment -- Part 2: Electrical loads
ISO 21848:2005 Road vehicles -- Electrical and electronic equipment for a supply voltage of 42 V -- Electrical loads
ISO 6165:2012 Earth-moving machinery -- Basic types -- Identification and terms and definitions
ISO 7637-1:2015 Road vehicles -- Electrical disturbances from conduction and coupling -- Part 1: Definitions and general considerations
ISO 7637-2:2011 Road vehicles -- Electrical disturbances from conduction and coupling -- Part 2: Electrical transient conduction along supply lines only
ISO/TR 12603:2010 Building construction machinery and equipment -- Classification