This document specifies requirements for the periodic inspection, examination and testing of offshore freight and service containers, built in accordance with ISO 10855-1, with maximum a gross mass not exceeding 25 000 kg and their associated lifting sets, intended for repeated use to, from and between offshore installations and ships. Inspection requirements following damage and repair of offshore containers are also included. Recommended knowledge and experience of staff responsible for inspection of offshore containers is given in Annex B. Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers is given in Annex C.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Container inspection plate
5.1 General
5.2 Contents of inspection plate
6 Schedule of periodic inspection/examination and test — Containers
7 Container lifting test
7.1 General
7.2 Test equipment and calibration
8 Non-destructive examination (NDE) of welds
8.1 General
8.2 NDE methods
8.3 Use of Eddy Current Testing at periodic inspections
8.4 NDE operators
9 Visual inspection
9.1 General
9.2 Markings
9.3 Welds
9.4 Pad eyes and lashing points
9.5 Structure
9.6 Door closures
9.7 Floor
10 Marking of the inspection plate
11 Inspection report
12 Record keeping
13 Damage and repair procedures
14 Schedule of inspection/examination and test — Lifting sets
15 Inspection of attachment of lifting set to an offshore container
15.1 Attachment
15.2 Inspection report
15.3 Record keeping
16 Pre-trip inspections
Annex A Regulations for offshore containers (informative)
Annex B Recommended knowledge and experience of staff responsible for inspection of offshore containers (informative)
Annex C Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers (informative)
6 Schedule of periodic inspection/examination and test — Containers
7 Container lifting test
7.1 General
7.2 Test equipment and calibration
8 Non-destructive examination (NDE) of welds
8.1 General
8.2 NDE methods
8.3 Use of Eddy Current Testing at periodic inspections
8.4 NDE operators
9 Visual inspection
9.1 General
9.2 Markings
9.3 Welds
9.4 Pad eyes and lashing points
9.5 Structure
9.6 Door closures
9.7 Floor
10 Marking of the inspection plate
11 Inspection report
12 Record keeping
13 Damage and repair procedures
14 Schedule of inspection/examination and test — Lifting sets
15 Inspection of attachment of lifting set to an offshore container
15.1 Attachment
15.2 Inspection report
15.3 Record keeping
16 Pre-trip inspections
Annex A Regulations for offshore containers (informative)
Annex B Recommended knowledge and experience of staff responsible for inspection of offshore containers (informative)
Annex C Recommended knowledge and experience of staff responsible for inspection of lifting sets intended for use with offshore containers (informative)
EN 13414-2:2003+A2:2008 Steel wire rope slings - Safety - Part 2: Specification for information for use and maintenance to be provided by the manufacturer
EN 818-4:1996+A1:2008 Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8
EN 818-6:2000+A1:2008 Short link chain for lifting purposes - Safety - Part 6: Chain slings - Specification for information for use and maintenance to be provided by the manufacturer
EN 13414-2:2003+A2:2008 Steel wire rope slings - Safety - Part 2: Specification for information for use and maintenance to be provided by the manufacturer
EN 818-4:1996+A1:2008 Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8
EN 818-6:2000+A1:2008 Short link chain for lifting purposes - Safety - Part 6: Chain slings - Specification for information for use and maintenance to be provided by the manufacturer
ISO 10675-1:2016 Non-destructive testing of welds -- Acceptance levels for radiographic testing -- Part 1: Steel, nickel, titanium and their alloys
ISO 10675-2:2017 Non-destructive testing of welds -- Acceptance levels for radiographic testing -- Part 2: Aluminium and its alloys
ISO 10855-1:2018 Offshore containers and associated lifting sets -- Part 1: Design, manufacture and marking of offshore containers
ISO 10855-2:2018 Offshore containers and associated lifting sets -- Part 2: Design, manufacture and marking of lifting sets
ISO 11666:2018 Non-destructive testing of welds -- Ultrasonic testing -- Acceptance levels
ISO 17636-1:2013 Non-destructive testing of welds -- Radiographic testing -- Part 1: X- and gamma-ray techniques with film
ISO 17636-2:2013 Non-destructive testing of welds -- Radiographic testing -- Part 2: X- and gamma-ray techniques with digital detectors
ISO 17637:2016 Non-destructive testing of welds -- Visual testing of fusion-welded joints
ISO 17638:2016 Non-destructive testing of welds -- Magnetic particle testing
ISO 17640:2017 Non-destructive testing of welds -- Ultrasonic testing -- Techniques, testing levels, and assessment
ISO 23277:2015 Non-destructive testing of welds -- Penetrant testing -- Acceptance levels
ISO 23278:2015 Non-destructive testing of welds -- Magnetic particle testing -- Acceptance levels
ISO 3452-1:2013 Non-destructive testing -- Penetrant testing -- Part 1: General principles
ISO 3834-2:2005 Quality requirements for fusion welding of metallic materials -- Part 2: Comprehensive quality requirements
ISO 5817:2014 Welding -- Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) -- Quality levels for imperfections
ISO 9712:2012 Non-destructive testing -- Qualification and certification of NDT personnel
ISO/IEC 17020:2012