This European Standard is applicable to residential solid fuel burning appliances. This European Standard specifies requirements relating to the design, manufacture, construction, safety and performance (efficiency and emission) of appliances fired by solid fuel (hereafter referred to as appliance(s)) and provides instructions for them. Furthermore, it also gives provisions for the evaluation of conformity i.e. initial type testing (ITT) and factory production control (FPC) and marking of these appliances. This European Standard also covers CO, NOx, OGC and particulate matter (PM / PME - see Annex F) emission test methods, however this European Standard does not contain any values for the limit on these emissions. Appliances receiving combustion air through ductwork from outside the external envelope, which is not air tight, are not considered roomsealed.This European Standard is not applicable to appliances with boiler parts in contact with fire or flue gases other than when the boiler parts are manufactured from steel or cast iron. This European Standard is not applicable to appliances with a boiler intended for water systems having - water temperatures above 110 °C and/or an operating pressure of more than 3 bar; - direct contact with sanitary hot water. This European Standard does not cover appliances to be operated with ventilating systems which are intended to operate with pressure below - 15 Pa in the room of installation of the appliance in relation to the outside atmosphere. This European Standard does not cover appliances intended to carry the load of a chimney.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10027-2:2015 Designation systems for steels - Part 2: Numerical system
EN 10028-2:2017 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10027-2:2015 Designation systems for steels - Part 2: Numerical system
EN 10028-2:2017 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10028-3:2017 Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10111:2008 Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions
EN 10120:2017 Steel sheet and strip for welded gas cylinders
EN 10216-1:2013 Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties
EN 10222-4:2017 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
EN 10222-4:2017+A1 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
EN 10222-4:2017+A1:2021 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
EN 12619:2013 Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method
EN 12828:2012+A1:2014 Heating systems in buildings - Design for water-based heating systems
EN 13384-2:2015+A1:2019 Chimneys - Thermal and fluid dynamic calculation methods - Part 2: Chimneys serving more than one combustion appliance
EN 14597:2012 Temperature control devices and temperature limiters for heat generating systems
EN 14792:2017 Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence
EN 14793:2017 Stationary source emissions - Demonstration of equivalence of an alternative method with a reference method
EN 15250:2007 Slow heat release appliances fired by solid fuel - Requirements and test methods
EN 1561:2011 Founding - Grey cast irons
EN 1563:2011 Founding - Spheroidal graphite cast irons
EN 303-5:2012 Heating boilers - Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW - Terminology, requirements, testing and marking
EN 60335-2-102:2016 Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections
EN 60730-1:2016 Automatic electrical controls - Part 1: General requirements
EN ISO 16948:2015 Solid biofuels - Determination of total content of carbon, hydrogen and nitrogen (ISO 16948:2015)
EN ISO 16994:2016 Solid biofuels - Determination of total content of sulfur and chlorine (ISO 16994:2016)
EN ISO 18122:2015 Solid biofuels - Determination of ash content (ISO 18122:2015)
EN ISO 18123:2015 Solid biofuels - Determination of the content of volatile matter (ISO 18123:2015)
EN ISO 18125:2017 Solid biofuels - Determination of calorific value (ISO 18125:2017)
EN ISO 18134-1:2015 Solid biofuels - Determination of moisture content - Oven dry method - Part 1: Total moisture - Reference method (ISO 18134-1:2015)
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 228-2:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987)
EN ISO 9606-1:2017 Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013)
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
ISO 10849:1996 Stationary source emissions -- Determination of the mass concentration of nitrogen oxides -- Performance characteristics of automated measuring systems
ISO 1171:2010 Solid mineral fuels -- Determination of ash
ISO 1928:2009 Solid mineral fuels -- Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value
ISO 19579:2006 Solid mineral fuels -- Determination of sulfur by IR spectrometry
ISO 331:1983 Coal -- Determination of moisture in the analysis sample -- Direct gravimetric method
ISO 334:2013 Solid mineral fuels -- Determination of total sulfur -- Eschka method
ISO 501:2012 Hard coal -- Determination of the crucible swelling number
ISO 562:2010 Hard coal and coke -- Determination of volatile matter
ISO 609:1996 Solid mineral fuels -- Determination of carbon and hydrogen -- High temperature combustion method
ISO 687:2010 Solid mineral fuels -- Coke -- Determination of moisture in the general analysis test sample
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 7-2:2000 Pipe threads where pressure-tight joints are made on the threads -- Part 2: Verification by means of limit gauges