Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks. Part 3: Lining with close-fit pipes (ISO 11296-3:2018)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This document, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit lining systems used for the renovation of underground non-pressure drainage and sewerage networks. It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) as manufactured, as well to the installed lining system with its associated joints.
Tämän julkaisun valmistelusta Suomessa vastaa Muoviteollisuus ry, puh. 09 172 841 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 General
3.2 Techniques
3.3 Characteristics
3.4 Materials
3.5 Product stages
3.6 Service conditions
3.7 Joints
4 Symbols and abbreviated terms
5 Pipes at the “M” stage
5.1 Materials
5.2 General characteristics
5.3 Material characteristics
5.4 Geometric characteristics
5.5 Mechanical characteristics
5.6 Physical characteristics
5.7 Jointing
5.8 Marking
6 Fittings at the “M” stage
7 Ancillary components
8 Fitness for purpose of the installed lining system at the “I” stage
8.1 Materials
8.2 General characteristics
8.3 Material characteristics
8.4 Geometric characteristics
8.5 Mechanical characteristics
8.6 Physical characteristics
8.7 Additional characteristics
8.8 Sampling
9 Installation practice
9.1 Preparatory work
9.2 Storage, handling and transport of pipes and fittings
9.3 Equipment
9.4 Installation
9.5 Process-related inspection and testing
9.6 Lining termination
9.7 Reconnection to existing manholes and laterals
9.8 Documentation
9.9 Final inspection and testing
Annex A Factory-folded heat-reverted polyethylene (PE) pipe — Determination of memory ability (normative)
ISO 11296-1:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks -- Part 1: General
ISO 12176-1:2017 Plastics pipes and fittings -- Equipment for fusion jointing polyethylene systems -- Part 1: Butt fusion
ISO 12176-2:2008 Plastics pipes and fittings -- Equipment for fusion jointing polyethylene systems -- Part 2: Electrofusion
ISO 11296-1:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks -- Part 1: General
ISO 12176-1:2017 Plastics pipes and fittings -- Equipment for fusion jointing polyethylene systems -- Part 1: Butt fusion
ISO 12176-2:2008 Plastics pipes and fittings -- Equipment for fusion jointing polyethylene systems -- Part 2: Electrofusion
ISO 13953:2001 Polyethylene (PE) pipes and fittings -- Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 18373-1:2007 Rigid PVC pipes -- Differential scanning calorimetry (DSC) method -- Part 1: Measurement of the processing temperature
ISO 2507-1:1995 Thermoplastics pipes and fittings -- Vicat softening temperature -- Part 1: General test method
ISO 3126:2005 Plastics piping systems -- Plastics components -- Determination of dimensions
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage -- Unplasticized poly(vinyl chloride) (PVC-U)
ISO 527-2:2012 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics
ISO 6259-1:2015 Thermoplastics pipes -- Determination of tensile properties -- Part 1: General test method
ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage -- Polyethylene (PE)
ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes -- Dichloromethane resistance at specified temperature (DCMT) -- Test method
ISO 9967:2016 Thermoplastics pipes -- Determination of creep ratio
ISO 9969:2016 Thermoplastics pipes -- Determination of ring stiffness