SFS-EN 10025-4:2019

Scope

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness = 150 mm. The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

The standards writing body responsible for this document in Finland is Mechanical Engineering and Metals Industry Standardization in Finland.

Table of contents

Product group(s)

77.140.10 Heat-treatable steels »
77.140.50 Flat steel products and semi-products »

Relationships

Normative references

CEN/TR 10347:2006 Guidance for forming of structural steels in processing
CR 10320:2004 Optical emission analysis of low alloy steels (routine method) - Method for determination of C, Si, S, P, Mn, Cr, Ni and Cu
EN 10017:2004 Steel rod for drawing and/or cold rolling - Dimensions and tolerances

CEN/TR 10347:2006 Guidance for forming of structural steels in processing
CR 10320:2004 Optical emission analysis of low alloy steels (routine method) - Method for determination of C, Si, S, P, Mn, Cr, Ni and Cu
EN 10017:2004 Steel rod for drawing and/or cold rolling - Dimensions and tolerances
EN 10020:2000 Definition and classification of grades of steel
EN 10021:2006 General technical delivery conditions for steel products
EN 10024:1995 Hot rolled taper flange I sections - Tolerances on shape and dimensions
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10027-1:2016 Designation systems for steels - Part 1: Steel names
EN 10027-2:2015 Designation systems for steels - Part 2: Numerical system
EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
EN 10034:1993 Structural steel I and H sections - Tolerances on shape and dimensions
EN 10048:1996 Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051:2010 Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
EN 10055:1995 Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions
EN 10056-1:2017 Structural steel equal and unequal leg angles - Part 1: Dimensions
EN 10056-2:1993 Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions
EN 10058:2018 Hot rolled flat steel bars and steel wide flats for general purposes - Dimensions and tolerances on shape and dimensions
EN 10059:2003 Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions
EN 10060:2003 Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions
EN 10061:2003 Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions
EN 10067:1996 Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass
EN 10079:2007 Definition of steel products
EN 1011-2:2001 Welding - Recommendations for welding of metallic materials - Part 2: Arc welding of ferritic steels
EN 10160:1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
EN 10163-1:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
EN 10163-2:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
EN 10163-3:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections
EN 10164:2018 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 10168:2004 Steel products - Inspection documents - List of information and description
EN 10204:2004 Metallic products - Types of inspection documents
EN 10279:2000 Hot rolled steel channels - Tolerances on shape, dimensions and mass
EN 10306:2001 Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams
EN 10308:2001 Non destructive testing - Ultrasonic testing of steel bars
EN 10315:2006 Routine method for analysis of high alloy steel by X-ray Fluorescence Spectrometry (XRF) by using a near by technique
EN 10363:2016 Continuously hot-rolled patterned steel strip and plate/sheet cut from wide strip - Tolerances on dimensions and shape
EN 10365:2017 Hot rolled steel channels, I and H sections - Dimensions and masses
EN ISO 14284:2002 Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996)
EN ISO 14284:2022 Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:2022)
EN ISO 14713-2:2009 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009)
EN ISO 148-1:2016 Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016)
EN ISO 15350:2010 Steel and iron - Determination of total carbon and sulfur content - Infrared absorption method after combustion in an induction furnace (routine method) (ISO 15350:2000)
EN ISO 2566-1:1999 Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984)
EN ISO 2566-1:2021 Steel - Conversion of elongation values - Part 1: Carbon and low-alloy steels (ISO 2566-1:2021)
EN ISO 377:2017 Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)
EN ISO 9443:2018 Surface quality classes for hot-rolled bars and wire rod (ISO 9443:2018)

Technical committee

CEN/TC 459/SC 3 Structural steels other than reinforcements »

Date of implementation

23.08.2019

Withdrawn

16.12.2022

Edition

2

Pages

61

Language(s)

Finnish/English

SFS-EN 10025-4:2019 Withdrawn