IEC 62109-1:2010 ed1.0 (2010-04)

Soveltamisala

IEC 62109-1:2010 applies to the power conversion equipment (PCE) for use in photovoltaic systems where a uniform technical level with respect to safety is necessary. Defines the minimum requirements for the design and manufacture of PCE for protection against electric shock, energy, fire, mechanical and other hazards. Provides general requirements applicable to all types of PV PCE.

Tuoteryhmä(t)

27.160 Solar energy engineering »

Sidokset

Velvoittavat viittaukset

ANSI UL 746B Polymeric Materials – Long Term Property Evaluations
ANSI UL 746C Polymeric Materials – Use in Electrical Equipment Evaluations
ANSI/ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials

ANSI UL 746B Polymeric Materials – Long Term Property Evaluations
ANSI UL 746C Polymeric Materials – Use in Electrical Equipment Evaluations
ANSI/ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM E162 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
IEC 60060-1 High-voltage test techniques – Part 1: General definitions and test requirements
IEC 60085 Electrical insulation – Thermal evaluation and designation
IEC 60112 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60216-1 Electrical insulating materials – Properties of thermal endurance – Part 1: Ageing procedures and evaluation of test results
IEC 60216-2 Electrical insulating materials – Thermal endurance properties – Part 2: Determination of thermal endurance properties of electrical insulating materials – Choice of test criteria
IEC 60216-3 Electrical insulating materials – Thermal endurance properties – Part 3: Instructions for calculating thermal endurance characteristics
IEC 60216-4-1 Electrical insulating materials – Thermal endurance properties – Part 4-1: Ageing ovens – Section 1: Single-chamber ovens
IEC 60216-5 Electrical insulating materials – Thermal endurance properties – Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
IEC 60216-6 Electrical insulating materials – Thermal endurance properties – Part 6: Determination of thermal endurance indices (TI and RTE) of an insulating material using the fixed time frame method
IEC 60227-1:2007 Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 1: General requirements
IEC 60245-1:2003 Rubber insulated cables – Rated voltages up to and including 450/750 V – Part 1: General requirements
IEC 60309 (all parts) Plugs, socket-outlets and couplers for industrial purposes
IEC 60320 (all parts) Appliances couplers for household and similar general purposes
IEC 60364-1:2005 Low-voltage electrical installations – Part 1: Fundamental principles, assessment of general characteristics, definitions
IEC 60364-5-54 Electrical installations of buildings – Part 5-54: Selection and erection of electrical equipment – Earthing arrangements, protective conductors and protective bonding conductors
IEC 60417 Graphical symbols for use on equipment
IEC 60529 Degrees of protection provided by enclosures (IP Code)
IEC 60664 (all parts) Insulation coordination for equipment within low-voltage systems
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems – Part 1: Principles, requirements and tests
IEC 60664-3:2003 Insulation coordination for equipment within low-voltage systems – Part 3: Use of coating, potting or moulding for protection against pollution
IEC 60664-4:2005 Insulation coordination for equipment within low-voltage systems – Part 4: Consideration of high-frequency voltage stress
IEC 60695-11-10 Fire hazard testing – Part 11-10: Test flames – 50 W horizontal and vertical flame test methods
IEC 60695-11-20 Fire hazard testing – Part 11- 20: Test flames – 500 W flame test methods
IEC 60695-11-5 Fire hazard testing – Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory test arrangement and guidance
IEC 60695-2-11 Fire hazard testing – Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test method for end-products
IEC 60695-2-20 Fire hazard testing – Part 2-20: Glowing/hot wire based test methods – Hot-wire coil ignitability – Apparatus, test method and guidance
IEC 60730-1:2010 Automatic electrical controls for household and similar use – Part 1: General requirements
IEC 60755 General requirements for residual current operated protective devices
IEC 60950-1:2005 Information technology equipment – Safety – Part 1: General requirements
IEC 60990:1999 Methods of measurement of touch current and protective conductor current
IEC 61032 Protection of persons and equipment by enclosures – Probes for verification
IEC 61180-1 High-voltage test techniques for low voltage equipment – Part 1: Definitions, test and procedure requirements
IEC 62020 Electrical accessories – Residual current monitors for household and similar uses (RCMs)
ISO 178 Plastics – Determination of flexural properties
ISO 179 (all parts) Plastics – Determination of Charpy impact properties
ISO 180 Plastics – Determination of Izod impact strength
ISO 261 ISO general purpose metric screw threads – General plan
ISO 262 ISO general purpose metric screw threads – Selected sizes for screws, bolts and nuts
ISO 3746 Acoustics – Determination of sound power levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane
ISO 4892-1 Plastics – Methods of exposure to laboratory light sources – Part 1: General guidance
ISO 4892-2 Plastics – Methods of exposure to laboratory light sources – Part 2: Xenon-arc lamps
ISO 4892-4 Plastics – Methods of exposure to laboratory light sources – Part 4: Open-flame carbon-arc lamps
ISO 527 (all parts) Plastics – Determination of tensile properties
ISO 7000 Graphical symbols for use on equipment – Index and synopsis
ISO 8256 Plastics – Determination of tensile-impact strength
ISO 9614-1 Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 1: Measurement at discrete points
ISO 9614-2 Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 2: Measurement by scanning
ISO 9614-3 Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 3: Precision method for measurement by scanning

Tekninen komitea

IEC/TC 82 Solar photovoltaic energy systems »

Vahvistuspäivä

28.04.2010

Julkaisupäivä

28.04.2010

Painos

1.0

Sivumäärä

316

Julkaisun kieli

englanti