ISO/IEC 14763-3:2014

Soveltamisala

This part of ISO/IEC 14763 specifies systems and methods for the inspection and testing of installed optical fibre cabling designed in accordance with premises cabling standards including ISO/IEC 11801, ISO/IEC 24764, ISO/IEC 24702 and ISO/IEC 15018. The test methods refer to existing standards-based procedures where they exist.

Sisällysluettelo

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and abbreviations

3.1 Terms and definitions
3.2 Abbreviations
3.3 Symbols

4 Conformance
5 General requirements

5.1 Test system
5.2 Reference measurement and calibration
5.3 Environmental conditions
5.4 Documentation

6 Test equipment

6.1 Light source and power meter
6.2 OTDR
6.3 Test cords and adapters
6.4 MMF launched modal distribution
6.5 SMF launch condition

7 Inspection equipment
8 Cabling under test – Channels and permanent links

8.1 General
8.2 Reference planes
8.3 Wavelength of measurement
8.4 Direction of measurement

9 Testing of installed cabling

9.1 Attenuation
9.2 Propagation delay
9.3 Length

10 Testing of cabling components within installed cabling

10.1 Attenuation of optical fibre cable
10.1.2 Measurement uncertainty
10.2 Attenuation of local and remote test interfaces
10.3 Attenuation of connecting hardware
10.4 Return loss of connecting hardware
10.5 Optical fibre length
10.6 Attenuation of cords

11 Inspection of cabling and cabling components

11.1 Optical fibre continuity
11.2 Cabling polarity
11.3 Optical fibre cable length
11.4 Inspection of optical fibre end faces
11.5 Optical fibre core size

Annex A Launch modal conditions for testing multimode optical fibre cabling (normative)
Annex B Visual inspection criteria for connectors (normative)
Annex C Optical time domain reflectometry (informative)
Annex D Inspection and testing of test and substitution test cords (normative)
Annex E Enhanced three-test-cord and one-test-cord reference methods for link and channel attenuation (informative)
Annex F Quality planning (informative)
Annex G Examples of calculations of channel and permanent link limits (informative)
Annex H Cleaning and inspection of fibre optic connections (informative)

Näytä kaikki

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and abbreviations

3.1 Terms and definitions
3.2 Abbreviations
3.3 Symbols

4 Conformance
5 General requirements

5.1 Test system
5.2 Reference measurement and calibration
5.3 Environmental conditions
5.4 Documentation

6 Test equipment

6.1 Light source and power meter
6.2 OTDR
6.3 Test cords and adapters
6.4 MMF launched modal distribution
6.5 SMF launch condition

7 Inspection equipment
8 Cabling under test – Channels and permanent links

8.1 General
8.2 Reference planes
8.3 Wavelength of measurement
8.4 Direction of measurement

9 Testing of installed cabling

9.1 Attenuation
9.2 Propagation delay
9.3 Length

10 Testing of cabling components within installed cabling

10.1 Attenuation of optical fibre cable
10.1.2 Measurement uncertainty
10.2 Attenuation of local and remote test interfaces
10.3 Attenuation of connecting hardware
10.4 Return loss of connecting hardware
10.5 Optical fibre length
10.6 Attenuation of cords

11 Inspection of cabling and cabling components

11.1 Optical fibre continuity
11.2 Cabling polarity
11.3 Optical fibre cable length
11.4 Inspection of optical fibre end faces
11.5 Optical fibre core size

Annex A Launch modal conditions for testing multimode optical fibre cabling (normative)
Annex B Visual inspection criteria for connectors (normative)
Annex C Optical time domain reflectometry (informative)
Annex D Inspection and testing of test and substitution test cords (normative)
Annex E Enhanced three-test-cord and one-test-cord reference methods for link and channel attenuation (informative)
Annex F Quality planning (informative)
Annex G Examples of calculations of channel and permanent link limits (informative)
Annex H Cleaning and inspection of fibre optic connections (informative)

Tuoteryhmä(t)

35.200 Interface and interconnection equipment »

Sidokset

Velvoittavat viittaukset

IEC 60050-731 International Electrotechnical Vocabulary — Chapter 731: Optical fibre communication
IEC 60825-2 Safety of laser products — Part 2: Safety of optical fibre communication systems (OFCS)
IEC 60874-14-3 Connectors for optical fibres and cables — Part 14-3: Detail specification for fibre optic adapter (simplex) type SC for single-mode fibre

IEC 60050-731 International Electrotechnical Vocabulary — Chapter 731: Optical fibre communication
IEC 60825-2 Safety of laser products — Part 2: Safety of optical fibre communication systems (OFCS)
IEC 60874-14-3 Connectors for optical fibres and cables — Part 14-3: Detail specification for fibre optic adapter (simplex) type SC for single-mode fibre
IEC 60874-19-1 Fibre optic interconnecting devices and passive components — Connectors for optical fibres and cables — Part 19-1: Fibre optic patch cord connector type SC-PC (floating duplex) standard terminated on multimode fibre type A1a, A1b — Detail specification
IEC 61280-1-3 Fibre optic communication subsystem test procedures — Part 1-3: General communication subsystems — Central Wavelength and spectral width measurement
IEC 61280-1-4 Fibre optic communication subsystem test procedures — Part 1-4: General communication subsystems — Light source encircled flux measurement method
IEC 61280-4-1 Fibre-optic communication subsystem test procedures — Part 4-1: Installed cable plant — Multimode attenuation measurement
IEC 61280-4-2 Fibre optic communication subsystem basic test procedures — Part 4-2: Fibre optic cable plant — Single-mode fibre optic cable plant attenuation
IEC 61300-3-35:2009 Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-35: Examinations and measurements — Fibre optic connector endface visual and automated inspection
IEC 61300-3-4 Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-4: Examinations and measurements — Attenuation
IEC 61300-3-42 Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-42: Examinations and measurements — Attenuation of single mode alignment sleeves and or adaptors with resilient alignment sleeves
IEC 61300-3-6 Fibre optic interconnecting devices and passive components — Basic test and measurement procedures — Part 3-6: Examinations and measurements — Return loss
IEC 61755-3-1 Fibre optic connector optical interfaces — Part 3-1: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical full zirconia PC ferrule, single mode fibre
IEC 61755-3-2 Fibre optic connector optical interfaces — Part 3-2: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical full zirconia ferrules for 8 degrees angled-PC single mode fibres
IEC 62614 Fibre optics — Launch condition requirements for measuring multimode attenuation
IEC 62664-1-1 Fibre optic interconnecting devices and passive components — Fibre optic connector product specifications — Part 1-1: LC-PC duplex multimode connectors terminated on IEC 60793-2-10 category A1a fibre
ISO/IEC 11801 Information technology — Generic cabling for customer premises
ISO/IEC 14763-2 Information technology — Implementation and operation of customer premises cabling — Part 2: Planning and installation

Tekninen komitea

ISO/IEC JTC 1/SC 25 Interconnection of information technology equipment »

Vahvistuspäivä

08.07.2014

Julkaisupäivä

08.07.2014

Painos

2014

Sivumäärä

51

Julkaisun kieli

englanti