SFS-EN 13480-8:2024:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

This document specifies requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480:2024 and CEN/TR 13480-7:2017. It specifies requirements for wrought products only.
NOTE Castings is not covered in this document.

Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).

Tuoteryhmä(t)

23.040.01 Putkistot ja niiden osat, yleistä »

Sidokset

Velvoittavat viittaukset

CEN ISO/TR 15608:2017 Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017)
EN 10204:2004 Metallic products - Types of inspection documents
EN 12392:2016+A1:2022 Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment

CEN ISO/TR 15608:2017 Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017)
EN 10204:2004 Metallic products - Types of inspection documents
EN 12392:2016+A1:2022 Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment
EN 13445-4:2021 Unfired pressure vessels - Part 4: Fabrication
EN 13480-1:2024 Metallic industrial piping - Part 1: General
EN 13480-2:2024 Metallic industrial piping - Part 2: Materials
EN 13480-3:2024 Metallic industrial piping - Part 3: Design and calculation
EN 13480-4:2024 Metallic industrial piping - Part 4: Fabrication and installation
EN 13480-5:2024 Metallic industrial piping - Part 5: Inspection and testing
EN 1779:1999 Non-destructive testing - Leak testing - Criteria for method and technique selection
EN 1779:1999/A1:2003 Non-destructive testing - Leak testing - Criteria for method and technique selection
EN 485-2:2016+A1:2018 Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
EN 485-3:2003 Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products
EN 485-4:1993 Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products
EN 573-3:2019+A1:2022 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 586-2:1994 Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements
EN 754-1:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery
EN 754-2:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
EN 754-7:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form
EN 754-8:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form
EN 755-1:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery
EN 755-2:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties
EN 755-7:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form
EN 755-8:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form
EN 755-9:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
EN 764-1:2015+A1:2016 Pressure equipment - Part 1: Vocabulary
EN 764-5:2002 Pressure Equipment - Part 5: Compliance and Inspection Documentation of Materials
EN ISO 10042:2018 Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections (ISO 10042:2018)
EN ISO 10893-11:2011 Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011)
EN ISO 10893-11:2011/A1:2020 Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections - Amendment 1: Change of ultrasonic test frequency; change of acceptance criteria (ISO 10893-11:2011/Amd 1:2020)
EN ISO 10893-8:2011 Non-destructive testing of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011)
EN ISO 10893-8:2011/A1:2020 Non-destructive testing of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections - Amendment 1: Change acceptance criteria (ISO 10893-8:2011/Amd 1:2020)
EN ISO 11666:2018 Non-destructive testing of welds - Ultrasonic testing - Acceptance levels (ISO 11666:2018)
EN ISO 148-1:2016 Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016)
EN ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
EN ISO 16810:2014 Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012)
EN ISO 16811:2014 Non-destructive testing - Ultrasonic testing - Sensitivity and range setting (ISO 16811:2012)
EN ISO 16823:2014 Non-destructive testing - Ultrasonic testing - Transmission technique (ISO 16823:2012)
EN ISO 16826:2014 Non-destructive testing - Ultrasonic testing - Examination for discontinuities perpendicular to the surface (ISO 16826:2012)
EN ISO 16827:2014 Non-destructive testing - Ultrasonic testing - Characterization and sizing of discontinuities (ISO 16827:2012)
EN ISO 16828:2014 Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012)
EN ISO 17636-1:2022 Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2022)
EN ISO 17636-2:2013 Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013)
EN ISO 17637:2016 Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016)
EN ISO 17639:2022 Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2022)
EN ISO 17640:2018 Non-destructive testing of welds - Ultrasonic testing - Techniques, testing levels, and assessment (ISO 17640:2018)
EN ISO 23277:2015 Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277:2015)
EN ISO 3452-1:2021 Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2021)
EN ISO 3834-2:2021 Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2021)
EN ISO 3834-3:2021 Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2021)
EN ISO 4063:2010 Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01)
EN ISO 4136:2022 Destructive tests on welds in metallic materials - Transverse tensile test (ISO 4136:2022)
EN ISO 5173:2010 Destructive tests on welds in metallic materials - Bend tests (ISO 5173:2009)
EN ISO 5173:2010/A1:2011 Destructive tests on welds in metallic materials - Bend tests - Amendment 1 (ISO 5173:2009/Amd 1:2011)
EN ISO 6892-1:2019 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2019)
EN ISO 6892-2:2018 Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2018)
EN ISO 7438:2020 Metallic materials - Bend test (ISO 7438:2020)
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
ISO/TR 25901-1:2016 Welding and allied processes — Vocabulary — Part 1: General terms
ISO/TR 25901-3:2016 Welding and allied processes — Vocabulary — Part 3: Welding processes
ISO/TR 25901-4:2016 Welding and allied processes — Vocabulary — Part 4: Arc welding

Tekninen komitea

CEN/TC 267 Industrial piping and pipelines »

Direktiivi

2014/68/EU

http://ec.europa.eu »

Vahvistuspäivä

02.08.2024

Julkaisupäivä

06.08.2024

Painos

4

Sivumäärä

45

Julkaisun kieli

englanti