Hot rolled products of structural steels. Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition. The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
CR 10320:2004 Optical emission analysis of low alloy steels (routine method) - Method for determination of C, Si, S, P, Mn, Cr, Ni and Cu
EN 10020:2000 Definition and classification of grades of steel
EN 10021:2006 General technical delivery conditions for steel products
CR 10320:2004 Optical emission analysis of low alloy steels (routine method) - Method for determination of C, Si, S, P, Mn, Cr, Ni and Cu
EN 10020:2000 Definition and classification of grades of steel
EN 10021:2006 General technical delivery conditions for steel products
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10027-1:2016 Designation systems for steels - Part 1: Steel names
EN 10027-2:2015 Designation systems for steels - Part 2: Numerical system
EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
EN 10048:1996 Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 10051:2010 Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape
EN 10079:2007 Definition of steel products
EN 1011-2:2001 Welding - Recommendations for welding of metallic materials - Part 2: Arc welding of ferritic steels
EN 10160:1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)
EN 10163-1:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
EN 10163-2:2004 Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
EN 10164:2018 Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
EN 10168:2004 Steel products - Inspection documents - List of information and description
EN 10204:2004 Metallic products - Types of inspection documents
EN 10315:2006 Routine method for analysis of high alloy steel by X-ray Fluorescence Spectrometry (XRF) by using a near by technique
EN ISO 14284:2002 Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996)
EN ISO 14284:2022 Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:2022)
EN ISO 14713-2:2009 Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009)
EN ISO 148-1:2016 Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016)
EN ISO 15350:2010 Steel and iron - Determination of total carbon and sulfur content - Infrared absorption method after combustion in an induction furnace (routine method) (ISO 15350:2000)
EN ISO 2566-1:1999 Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984)
EN ISO 2566-1:2021 Steel - Conversion of elongation values - Part 1: Carbon and low-alloy steels (ISO 2566-1:2021)
EN ISO 377:2017 Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017)
EN ISO 6892-1:2016 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016)