Verkkokauppa
SFS-EN 1993-1-3:en
Eurocode 3. Design of steel structures. Part 1-3: General rules. Supplementary rules for cold-formed members and sheeting
Soveltamisala
Suomenkielistä soveltamisalaa ei ole saatavissa.
(1) EN 1993-1-3 gives design requirements for cold-formed members and sheeting. It applies to cold-formed steel products made from coated or uncoated hot or cold rolled sheet or strip, that have been cold-formed by such processes as cold rolled forming or press braking. It may also be used for the design of profiled steel sheeting for composite steel and concrete slabs at the construction stage, see EN 1994. The execution of steel structures made of cold-formed members and sheeting is covered in EN 1090.
NOTE: The rules in this part complement the rules in other parts of EN 1993-1.
(2) Methods are also given for stressed-skin design using steel sheeting as a structural diaphragm.
(3) This part does not apply to cold-formed circular and rectangular structural hollow sections supplied to EN 10219, for which reference should be made to EN 1993-1-1 and EN 1993-1-8.
(4) EN 1993-1-3 gives methods for design by calculation and for design assisted by testing. The methods for design by calculation apply only within stated ranges of material properties and geometrical proportions for which sufficient experience and test evidence is available. These limitations do not apply to design assisted by testing.
(5) EN 1993-1-3 does not cover load arrangement for testing for loads during execution and maintenance.
(6) The calculation rules given in this standard are only valid if the tolerances of the cold formed members comply with EN 10162
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
(1) EN 1993-1-3 gives design requirements for cold-formed members and sheeting. It applies to cold-formed steel products made from coated or uncoated hot or cold rolled sheet or strip, that have been cold-formed by such processes as cold rolled forming or press braking. It may also be used for the design of profiled steel sheeting for composite steel and concrete slabs at the construction stage, see EN 1994. The execution of steel structures made of cold-formed members and sheeting is covered in EN 1090.
NOTE: The rules in this part complement the rules in other parts of EN 1993-1.
(2) Methods are also given for stressed-skin design using steel sheeting as a structural diaphragm.
(3) This part does not apply to cold-formed circular and rectangular structural hollow sections supplied to EN 10219, for which reference should be made to EN 1993-1-1 and EN 1993-1-8.
(4) EN 1993-1-3 gives methods for design by calculation and for design assisted by testing. The methods for design by calculation apply only within stated ranges of material properties and geometrical proportions for which sufficient experience and test evidence is available. These limitations do not apply to design assisted by testing.
(5) EN 1993-1-3 does not cover load arrangement for testing for loads during execution and maintenance.
(6) The calculation rules given in this standard are only valid if the tolerances of the cold formed members comply with EN 10162
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Tuoteryhmä(t)
Sidokset
Velvoittavat viittaukset
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
Näytä julkaisuun liittyvät velvoittavat viittaukset
Tekninen komitea
Direktiivi
Vahvistuspäivä
18.12.2006
Julkaisupäivä
12.01.2007
Painos
1
Sivumäärä
131
Julkaisun kieli
englanti
Lisätiedot
Tämä on nk. ensimmäisen sukupolven eurokoodi, joka on edelleen käytössä Suomessa, kunnes toisen sukupolven eurokoodit otetaan käyttöön. Lisätietoja eurokoodeista www.eurocodes.fi.