(1) EN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see section 3).
NOTE Minimum material thickness may be defined in the National Annex. The following limits are recommended – if not otherwise explicitly stated in this standard: - components with material thickness not less than 0,6 mm; - welded components with material thickness not less than 1,5 mm; - connections with: o steel bolts and pins with diameter not less than 5 mm; o aluminium bolts and pins with diameter not less than 8 mm; o rivets and thread forming screws with diameter not less than 4,2 mm
(2) The following subjects are dealt with in EN 1999-1-1: Section 1: General Section 2: Basis of design Section 3: Materials Section 4: Durability Section 5: Structural analysis Section 6: Ultimate limit states for members Section 7: Serviceability limit states Section 8: Design of joints Annex A Execution classes Annex B Equivalent T-stub in tension Annex C Materials selection Annex D Corrosion and surface protection Annex E Analytical models for stress strain relationship Annex F Behaviour of cross section beyond elastic limit Annex G Rotation capacity Annex H Plastic hinge method for continuous beams Annex I Lateral torsional buckling of beams and torsional or flexural-torsional buckling of compression members Annex J Properties of cross sections Annex K Shear lag effects in member design Annex L Classification of connections Annex M Adhesive bonded connections
(3) Sections 1 to 2 provide additional clauses to those given in EN 1990 “Basis of structural design”.
(4) Section 3 deals with material properties of products made of structural aluminium alloys.
(5) Section 4 gives general rules for durability.
(6) Section 5 refers to the structural analysis of structures, in which the members can be modelled with sufficient accuracy as line elements for global analysis.
(7) Section 6 g
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
EN 1011-4:2000 Welding - Recommendations for welding of metallic materials - Part 4: Arc welding of aluminium and aluminium alloys
EN 1090-1:2009+A1:2011 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
EN 1090-3:2019 Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures
EN 1011-4:2000 Welding - Recommendations for welding of metallic materials - Part 4: Arc welding of aluminium and aluminium alloys
EN 1090-1:2009+A1:2011 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
EN 1090-3:2019 Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures
EN 12681:2003 Founding - Radiographic examination
EN 13068-1:1999 Non-destructive testing - Radioscopic testing - Part 1: Quantitative measurement of imaging properties
EN 13068-2:1999 Non-destructive testing - Radioscopic testing - Part 2: Check of long term stability of imaging devices
EN 13068-3:2001 Non-destructive testing - Radioscopic testing - Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays
EN 1371-1:1997 Founding - Liquid penetrant inspection - Part 1: Sand, gravity die and low pressure die castings
EN 1559-1:1997 Founding - Technical conditions of delivery - Part 1: General
EN 1559-4:1999 Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings
EN 1592-1:1997 Aluminium and aluminium alloys - HF seam welded tubes - Part 1: Technical conditions for inspection and delivery
EN 1592-2:1997 Aluminium and aluminium alloys - HF seam welded tubes - Part 2: Mechanical properties
EN 1592-3:1997 Aluminium and aluminium alloys - HF seam welded tubes - Part 3: Tolerances on dimensions and form for circular tubes
EN 1592-4:1997 Aluminium and aluminium alloys - HF seam welded tubes - Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes
EN 1990:2002 Eurocode - Basis of structural design
EN 1991-1-1:2002 Eurocode 1: Actions on structures - Part 1-1: General actions - Densities, self-weight, imposed loads for buildings
EN 1991-1-2:2002 Eurocode 1: Actions on structures - Part 1-2: General actions - Actions on structures exposed to fire
EN 1991-1-3:2003 Eurocode 1 - Actions on structures - Part 1-3: General actions - Snow loads
EN 1991-1-3:2003/A1:2015 Eurocode 1 - Actions on structures - Part 1-3: General actions - Snow loads
EN 1991-1-4:2005 Eurocode 1: Actions on structures - Part 1-4: General actions - Wind actions
EN 1991-1-4:2005/A1:2010 Eurocode 1: Actions on structures - Part 1-4: General actions - Wind actions
EN 1991-1-5:2003 Eurocode 1: Actions on structures - Part 1-5: General actions - Thermal actions
EN 1991-1-6:2005 Eurocode 1 - Actions on structures Part 1-6: General actions - Actions during execution
EN 1991-1-7:2006 Eurocode 1 - Actions on structures - Part 1-7: General actions - Accidental actions
EN 1991-1-7:2006/A1:2014 Eurocode 1 - Actions on structures - Part 1-7: General actions - Accidental actions
EN 1991-2:2003 Eurocode 1: Actions on structures - Part 2: Traffic loads on bridges
EN 1991-3:2006 Eurocode 1 - Actions on structures - Part 3: Actions induced by cranes and machinery
EN 1991-4:2006 Eurocode 1 - Actions on structures - Part 4: Silos and tanks
EN 1993-1-1:2005 Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings
EN 1993-1-1:2022 Eurocode 3 - Design of steel structures - Part 1-1: General rules and rules for buildings
EN 1999-1-2:2007 Eurocode 9 - Design of aluminium structures - Part 1-2: Structural fire design
EN 1999-1-3:2007 Eurocode 9: Design of aluminium structures – Part 1-3: Structures susceptible to fatigue
EN 1999-1-4:2007 Eurocode 9 - Design of aluminium structures - Part 1-4: Cold-formed structural sheeting
EN 1999-1-5:2007 Eurocode 9 - Design of aluminium structures - Part 1-5: Shell structures
EN 28839:1991 Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986)
EN 444:1994 Non-destructive testing - General principles for radiographic examination of metallic materials by X- and gamma-rays
EN 485-1:1993 Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery
EN 485-2:1994 Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
EN 485-3:2003 Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products
EN 485-4:1993 Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products
EN 508-2:2000 Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 2: Aluminium
EN 515:2017 Aluminium and aluminium alloys - Wrought products - Temper designations
EN 571-1:1997 Non destructive testing - Penetrant testing - Part 1: General principles
EN 573-3:2019 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 573-3:2019+A1:2022 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN 586-1:1997 Aluminium and aluminium alloys - Forgings - Part 1: Technical conditions for inspection and delivery
EN 586-2:1994 Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements
EN 586-3:2001 Aluminium and aluminium alloys - Forgings - Part 3: Tolerances on dimensions and form
EN 754-1:1997 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery
EN 754-2:1997 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties
EN 754-3:1995 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form
EN 754-4:1995 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form
EN 754-5:1995 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form
EN 754-6:1995 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form
EN 754-7:1998 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form
EN 754-8:1998 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form
EN 755-1:1997 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery
EN 755-2:1997 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties
EN 755-3:1995 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form
EN 755-4:1995 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form
EN 755-5:1995 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form
EN 755-6:1995 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form
EN 755-7:1998 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form
EN 755-8:1998 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form
EN 755-9:2001 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
EN ISO 1302:2002 Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302:2002)
EN ISO 18273:2015 Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification (ISO 18273:2015)
EN ISO 3506-1:2020 Fasteners - Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs with specified grades and property classes (ISO 3506-1:2020)
EN ISO 4287:1998 Geometrical product specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters (ISO 4287:1997)
EN ISO 4288:1997 Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (ISO 4288:1996)
EN ISO 6892-1:2019 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2019)
EN ISO 6892-2:2018 Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2018)
EN ISO 6892-3:2015 Metallic materials - Tensile testing - Part 3: Method of test at low temperature (ISO 6892-3:2015)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
ISO 11003-1:2001 Adhesives -- Determination of shear behaviour of structural adhesives -- Part 1: Torsion test method using butt-bonded hollow cylinders
ISO 11003-2:2001 Adhesives -- Determination of shear behaviour of structural adhesives -- Part 2: Tensile test method using thick adherends
ISO 8930:1987 General principles on reliability for structures -- List of equivalent terms
Tätä versiota standardista voidaan käyttää 2028-03-30 saakka.
Tämä on nk. ensimmäisen sukupolven eurokoodi, joka on edelleen käytössä Suomessa, kunnes toisen sukupolven eurokoodit otetaan käyttöön. Lisätietoja eurokoodeista www.eurocodes.fi.