IEC 60079-7:2015(E) specifies the requirements for the design, construction, testing and marking of electrical equipment and Ex Components with type of protection increased safety "e" intended for use in explosive gas atmospheres. Electrical equipment and Ex Components of type of protection increased safety "e" are either:
- Level of Protection "eb" (EPL "Mb" or "Gb");
- or Level of Protection "ec" (EPL "Gc"). Level of Protection "eb" applies to equipment or Ex Components, including their connections, conductors, windings, lamps, and batteries; but not including semiconductors or electrolytic capacitors. Level of Protection "ec" applies to equipment or Ex Components, including their connections, conductors, windings, lamps, and batteries; and also including semiconductors and electrolytic capacitors. The requirements of this standard apply to both Levels of Protection unless otherwise stated. For Level of Protection "eb", this standard applies to electrical equipment where the rated voltage does not exceed 11 kV r.m.s., a.c. or d.c. For Level of Protection "ec", this standard applies to electrical equipment where the rated voltage does not exceed 15 kV r.m.s., a.c. or d.c. This standard supplements and modifies the general requirements of IEC 60079-0. Where a requirement of this standard conflicts with a requirement of IEC 60079-0, the requirement of this standard takes precedence. This fifth edition cancels and replaces the fourth edition published in 2006, and constitutes a technical revision. Refer to the Foreword of the document for a complete listing of the technical changes between edition 5.0 and previous edition of the document. Keywords: electrical equipment and Ex Components with type of protection increased safety "e" intended for use in explosive gas atmospheres.
Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.
EN 60034-1:2010 Rotating electrical machines - Part 1: Rating and performance
EN 60061-1:1993 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps
EN 60061-2:1993 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders
EN 60034-1:2010 Rotating electrical machines - Part 1: Rating and performance
EN 60061-1:1993 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps
EN 60061-2:1993 Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders
EN 60064:1995 Tungsten filament lamps for domestic and similar general lighting purposes - Performance requirements
EN 60068-2-27:2009 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
EN 60068-2-42:2003 Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections
EN 60068-2-6:2008 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
EN 60079-11:2012 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
EN 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
EN 60079-30-1:2017 Explosive atmospheres - Part 30-1: Electrical resistance trace heating - General and testing requirements
EN 60085:2008 Electrical insulation - Thermal evaluation and designation
EN 60216-1:2001 Electrical insulating materials - Properties of thermal endurance - Part 1: Ageing procedures and evaluation of test results
EN 60216-1:2013 Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
EN 60216-2:2005 Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria
EN 60228:2005 Conductors of insulated cables
EN 60317-13:2010 Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200
EN 60317-46:2014 Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240
EN 60317-8:2010 Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180
EN 60400:2017 Lampholders for tubular fluorescent lamps and starterholders
EN 60432-1:2000 Incandescent lamps - Safety specifications - Part 1: Tungsten filament lamps for domestic and similar general lighting purposes
EN 60432-2:2000 Incandescent lamps - Safety specifications - Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes
EN 60432-3:2013 Incandescent lamps - Safety specifications - Part 3: Tungsten-halogen lamps (non-vehicle)
EN 60598-1:1988 Luminaires - Part 1: General requirements and tests
EN 60598-1:2015 Valaisimet. Osa 1: Yleiset vaatimukset ja testit
EN 60947-1:2007 Pienjännitekytkinlaitteet. Osa 1: Pienjännitekytkinlaitteet. Yleiset vaatimukset
EN 60947-7-1:2009 Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors
EN 60947-7-2:2009 Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
EN 60998-2-4:2005 Kotitalouksiin ja vastaaviin käyttöihin tarkoitetut kytkentätarvikkeet. Osa 2-4: Kierrettävien huppuliittimien erityisvaatimukset
EN 60999-1:2000 Kytkentätarvikkeet. Kuparijohtimien liittämiseen tarkoitettujen ruuvityyppisten ja ruuvittomien puristusosien turvallisuusvaatimukset. Osa 1: Yleiset vaatimukset ja erityisvaatimukset 0,2 mm2 ... 35 mm2 johtimien liittämiseen tarkoitetuille puristusosille
EN 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included)
EN 61184:2017 Bayonet lampholders
EN 61195:1999 Double-capped fluorescent lamps - Safety specifications
EN 61347-1:2015 Lamp controlgear - Part 1: General and safety requirements
EN 61347-2-3:2011 Lamp control gear - Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps
EN 61869-2:2012 Instrument transformers - Part 2: Additional requirements for current transformers
EN 62035:2014 Discharge lamps (excluding fluorescent lamps) - Safety specifications
EN IEC 60079-0:2018 Räjähdysvaaralliset tilat. Osa 0: Laitteet. Yleiset vaatimukset
EN IEC 60112:2020 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
EN IEC 60238:2018 Edison screw lampholders
EN IEC 60598-1:2021 Luminaires - Part 1: General requirements and tests
EN IEC 60664-1:2020 Insulation coordination for equipment within low-voltage supply systems - Part 1: Principles, requirements and tests
EN IEC 60947-1:2021 Low-voltage switchgear and controlgear - Part 1: General rules
EN IEC 60947-7-4:2019 Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors
EN ISO 178:2019 Plastics - Determination of flexural properties (ISO 178:2019)
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
IEC 60317-3:2004 Specifications for particular types of winding wires - Part 3: Polyester enamelled round copper wire, class 155
IEC 60529:2001
ISO 2859-1:1999 Sampling procedures for inspection by attributes -- Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection