Verkkokauppa
SFS-EN IEC 61215-2:2021:en
Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
Soveltamisala
Suomenkielistä soveltamisalaa ei ole saatavissa.
IEC 61215-2:2021 is available as IEC 61215-2:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61215-2:2021 lays down requirements for the design qualification of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This document is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. The objective of this test sequence is to determine the electrical characteristics of the module and to show, as far as possible within reasonable constraints of cost and time, that the module is capable of withstanding prolonged exposure outdoors. This second edition of IEC 61215-2 cancels and replaces the first edition of IEC 61215-2 issued in 2016. This edition includes the following significant technical changes with respect to the previous edition:
a. Addition of cyclic (dynamic) mechanical load testing (MQT 20).
b. Addition of a test for detection of potential-induced degradation (MQT 21).
c. Addition of test methods required for bifacial PV modules.
d. Addition of test methods required for flexible modules. This includes the addition of the bending test (MQT 22).
e. Revision of simulator requirements to ensure uncertainty is both well-defined and minimized.
f. Correction to the hot spot endurance test, where the procedure for monolithically integrated (MLI) thin film technologies (MQT 09.2) previously included two sections describing a procedure only appropriate for silicon modules.
g. Selection of three diodes, rather than all, for testing in the bypass diode thermal test (MQT 18).
h. Removal of the nominal module operating test (NMOT), and associated test of performance at NMOT, from the IEC 61215 series.
Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.
IEC 61215-2:2021 is available as IEC 61215-2:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61215-2:2021 lays down requirements for the design qualification of terrestrial photovoltaic modules suitable for long-term operation in open-air climates. This document is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. The objective of this test sequence is to determine the electrical characteristics of the module and to show, as far as possible within reasonable constraints of cost and time, that the module is capable of withstanding prolonged exposure outdoors. This second edition of IEC 61215-2 cancels and replaces the first edition of IEC 61215-2 issued in 2016. This edition includes the following significant technical changes with respect to the previous edition:
a. Addition of cyclic (dynamic) mechanical load testing (MQT 20).
b. Addition of a test for detection of potential-induced degradation (MQT 21).
c. Addition of test methods required for bifacial PV modules.
d. Addition of test methods required for flexible modules. This includes the addition of the bending test (MQT 22).
e. Revision of simulator requirements to ensure uncertainty is both well-defined and minimized.
f. Correction to the hot spot endurance test, where the procedure for monolithically integrated (MLI) thin film technologies (MQT 09.2) previously included two sections describing a procedure only appropriate for silicon modules.
g. Selection of three diodes, rather than all, for testing in the bypass diode thermal test (MQT 18).
h. Removal of the nominal module operating test (NMOT), and associated test of performance at NMOT, from the IEC 61215 series.
Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.
Tuoteryhmä(t)
Sidokset
Velvoittavat viittaukset
Tekninen komitea
Vahvistuspäivä
23.04.2021
Julkaisupäivä
27.04.2021
Painos
1
Sivumäärä
59
Julkaisun kieli
englanti