This document specifies the characteristics of the following types of dowel-type fasteners: - nails; - staples; - screws; - dowels; - bolts with nuts. This document covers dowel-type fasteners for structural use in load bearing timber structures only. This document covers also the following additional intended uses of the screws: - to fix roof or cladding elements to the timber structure, with or without insulation layers; and - as reinforcement inserted in timber or in a glue laminated timber element to improve its resistance to compression perpendicular to the grain. This document covers types of dowel-type fasteners, which are manufactured of either carbon steel or stainless steel and which may be coated for the following purposes: - corrosion protection (as Type 1 coating); - lubrication, to facilitate insertion (as Type 2 coating); - withdrawal enhancement and/or collation for nails and staples (adhesive and/or resin coatings) (as Type 3 coating). This document covers types of dowel-type fasteners, which are manufactured from materials and within the specifications for their geometry related properties, only as they are specified for: - nails (see G.1); - staples (see G.2); - screws (see G.3); - dowels (see G.4); and - bolts with nuts (see G.5). This document specifies also the assessment and verification of constancy of performance (AVCP) procedures of these characteristics and includes provisions for marking of dowel-type fasteners. This document does not cover dowel-type fasteners treated with fire retardants to improve their fire performance, nor does it cover glued-in rods.
Tämän julkaisun valmistelusta Suomessa vastaa Rakennustuoteteollisuus RTT ry, puh. 09 12 991 (vaihde).
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10025-2:2019 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10025-3:2019 Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 10088-4:2009 Stainless steels - Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for construction purposes
EN 10088-5:2009 Stainless steels - Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion resisting steels for construction purposes
EN 10149-1:2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
EN 10204:2004 Metallic products - Types of inspection documents
EN 10218-1:2012 Steel wire and wire products - General - Part 1: Test methods
EN 10277:2018 Bright steel products - Technical delivery conditions
EN 13501-1:2018 Fire classification of construction products and building elements - Part 1: Classification using data from reaction to fire tests
EN 1382:2016 Timber Structures - Test methods - Withdrawal capacity of timber fasteners
EN 1383:2016 Timber structures - Test methods - Pull through resistance of timber fasteners
EN 13986:2004+A1:2015 Wood-based panels for use in construction - Characteristics, evaluation of conformity and marking
EN 14081-1:2016+A1:2019 Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements
EN 14358:2016 Timber structures - Calculation and verification of characteristic values
EN 15737:2009 Timber Structures - Test methods - Torsional resistance of driving in screws
EN 1990:2002 Eurocode - Basis of structural design
EN 1993-1-4:2006/A1:2015 Eurocode 3 - Design of steel structures - Part 1-4: General rules - Supplementary rules for stainless steels
EN 1995-1-1:2004 Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings
EN 1995-1-1:2004/A1:2008 Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings
EN 1995-1-1:2004/A2:2014 Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings
EN 409:2009 Timber structures - Test methods - Determination of the yield moment of dowel type fasteners
EN 634-2:2007 Cement-bonded particleboards - Specifications - Part 2: Requirements for OPC bonded particleboards for use in dry, humid and external conditions
EN 636:2012+A1:2015 Plywood - Specifications
EN ISO 10289:2001 Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates - Rating of test specimens and manufactured articles subjected to corrosion tests (ISO 10289:1999)
EN ISO 10666:1999 Drilling screws with tapping screw thread - Mechanical and functional properties (ISO 10666:1999)
EN ISO 10684:2004 Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
EN ISO 11997-1:2017 Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1: Wet (salt fog)/dry/humid (ISO 11997-1:2017)
EN ISO 1460:1994 Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric determination of the mass per unit area (ISO 1460:1992)
EN ISO 1463:2004 Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2003)
EN ISO 16120-1:2017 Non-alloy steel wire rod for conversion to wire - Part 1: General requirements (ISO 16120-1:2017)
EN ISO 16120-2:2017 Non-alloy steel wire rod for conversion to wire - Part 2: Specific requirements for general purpose wire rod (ISO 16120-2:2017)
EN ISO 16120-3:2011 Non-alloy steel wire rod for conversion to wire - Part 3: Specific requirements for rimmed and rimmed substitute, low-carbon steel wire rod (ISO 16120-3:2011)
EN ISO 16120-4:2017 Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4:2017)
EN ISO 2081:2018 Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2018)
EN ISO 2178:2016 Non-magnetic coatings on magnetic substrates - Measurement of coating thickness - Magnetic method (ISO 2178:2016)
EN ISO 21968:2019 Non-magnetic metallic coatings on metallic and non-metallic basis materials - Measurement of coating thickness - Phase-sensitive eddy-current method (ISO 21968:2019)
EN ISO 3497:2000 Metallic coatings - Measurement of coating thickness - X-ray spectrometric methods (ISO 3497:2000)
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
EN ISO 4042:2018 Fasteners - Electroplated coating systems (ISO 4042:2018)
EN ISO 6270-1:2018 Paints and varnishes - Determination of resistance to humidity - Part 1: Condensation (single-sided exposure) (ISO 6270-1:2017)
EN ISO 6892-1:2019 Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2019)
EN ISO 8407:2014 Corrosion of metals and alloys - Removal of corrosion products from corrosion test specimens (ISO 8407:2009)
EN ISO 8565:2011 Metals and alloys - Atmospheric corrosion testing - General requirements (ISO 8565:2011)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
EN ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread (ISO 898-2:2012)
EN ISO 9226:2012 Corrosion of metals and alloys - Corrosivity of atmospheres - Determination of corrosion rate of standard specimens for the evaluation of corrosivity (ISO 9226:2012)
EN ISO 9227:2017 Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017)
ISO 965-1:2013 ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 965-2:1998 ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
ISO 965-3:1998 ISO general purpose metric screw threads — Tolerances — Part 3: Deviations for constructional screw threads
ISO 965-4:1998 ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
ISO 965-5:1998 ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing