SFS-EN ISO 10931:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 10931:2005 specifies the characteristics and requirements for components such as pipes, fittings and valves made from poly (vinylidene fluoride) (PVDF), intended to be used for thermoplastics piping systems in the field of industrial applications above-ground.

Tämän julkaisun valmistelusta Suomessa vastaa Muoviteollisuus ry, puh. 09 172 841 (vaihde).

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions

3.1 Geometrical definitions
3.2 Material definitions
3.3 Definitions related to material characteristics
3.4 Definitions related to service conditions

4 Symbols and abbreviated terms

4.1 Symbols
4.2 Abbreviations

5 Material

5.1 General
5.2 Hydrostatic strength properties
5.3 Material characteristics
5.4 Reprocessable and recyclable material
5.5 Materials for parts not made from PVDF

6 General characteristics — Appearance
7 Geometrical characteristics

7.1 General
7.2 Diameters and related tolerances
7.3 Wall thicknesses and related tolerances
7.4 Angles
7.5 Laying lengths
7.6 Threads
7.7 Mechanical fittings
7.8 Joint dimensions of valves

8 Mechanical characteristics

8.1 Resistance to internal pressure of components
8.2 Calculation of the test pressure for components

9 Physical characteristics
10 Chemical characteristics

10.1 Effect on component material(s)
10.2 Effect on fluids

11 Electrical characteristics
12 Performance requirements

12.1 General
12.2 Preparation of test assemblies
12.3 Fusion compatibility
12.4 Permanent jointing

13 Classification of components
14 Design of a thermoplastics piping system for industrial applications
15 Installation of piping systems
16 Declaration of compliance with this International Standard
17 Marking

17.1 General
17.2 Minimum required marking of pipes
17.3 Minimum required marking of fittings
17.4 Minimum required marking of valves

18 Manufacture

Annex A Specific characteristics and requirements for industrial piping systems made from poly(vinylidene fluoride) (PVDF) (informative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions

3.1 Geometrical definitions
3.2 Material definitions
3.3 Definitions related to material characteristics
3.4 Definitions related to service conditions

4 Symbols and abbreviated terms

4.1 Symbols
4.2 Abbreviations

5 Material

5.1 General
5.2 Hydrostatic strength properties
5.3 Material characteristics
5.4 Reprocessable and recyclable material
5.5 Materials for parts not made from PVDF

6 General characteristics — Appearance
7 Geometrical characteristics

7.1 General
7.2 Diameters and related tolerances
7.3 Wall thicknesses and related tolerances
7.4 Angles
7.5 Laying lengths
7.6 Threads
7.7 Mechanical fittings
7.8 Joint dimensions of valves

8 Mechanical characteristics

8.1 Resistance to internal pressure of components
8.2 Calculation of the test pressure for components

9 Physical characteristics
10 Chemical characteristics

10.1 Effect on component material(s)
10.2 Effect on fluids

11 Electrical characteristics
12 Performance requirements

12.1 General
12.2 Preparation of test assemblies
12.3 Fusion compatibility
12.4 Permanent jointing

13 Classification of components
14 Design of a thermoplastics piping system for industrial applications
15 Installation of piping systems
16 Declaration of compliance with this International Standard
17 Marking

17.1 General
17.2 Minimum required marking of pipes
17.3 Minimum required marking of fittings
17.4 Minimum required marking of valves

18 Manufacture

Annex A Specific characteristics and requirements for industrial piping systems made from poly(vinylidene fluoride) (PVDF) (informative)

Bibliography

Tuoteryhmä(t)

23.040.01 Putkistot ja niiden osat, yleistä »

Sidokset

Velvoittavat viittaukset

IEC 60364-1:2005
IEC 60449:1973
IEC 60529:1989

IEC 60364-1:2005
IEC 60449:1973
IEC 60529:1989
ISO 1043-1:2001 Plastics -- Symbols and abbreviated terms -- Part 1: Basic polymers and their special characteristics
ISO 11357-3:1999 Plastics -- Differential scanning calorimetry (DSC) -- Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 1167:1996 Thermoplastics pipes for the conveyance of fluids -- Resistance to internal pressure -- Test method
ISO 1183-2:2004 Plastics -- Methods for determining the density of non-cellular plastics -- Part 2: Density gradient column method
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids -- Dimensions and tolerances -- Part 1: Metric series
ISO 12092:2000 Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure -- Resistance to internal pressure -- Test method
ISO 12162:1995 Thermoplastics materials for pipes and fittings for pressure applications -- Classification and designation -- Overall service (design) coefficient
ISO 15853:1999 Thermoplastics materials -- Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding
ISO 16135:2006 Industrial valves -- Ball valves of thermoplastics materials
ISO 16136:2006 Industrial valves -- Butterfly valves of thermoplastics materials
ISO 16137:2006 Industrial valves -- Check valves of thermoplastics materials
ISO 16138:2006 Industrial valves -- Diaphragm valves of thermoplastics materials
ISO 16139:2006 Industrial valves -- Gate valves of thermoplastics materials
ISO 21787:2006 Industrial valves -- Globe valves of thermoplastics materials
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 2505-1:1994 Thermoplastics pipes -- Longitudinal reversion -- Part 1: Determination methods
ISO 2505-2:1994 Thermoplastics pipes -- Longitudinal reversion -- Part 2: Determination parameters
ISO 265-1:1988 Pipes and fittings of plastics materials -- Fittings for domestic and industrial waste pipes -- Basic dimensions: Metric series -- Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
ISO 3126:2005 Plastics piping systems -- Plastics components -- Determination of dimensions
ISO 4065:1996 Thermoplastics pipes -- Universal wall thickness table
ISO 472:1999 Plastics -- Vocabulary
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 9080:2003 Plastics piping and ducting systems -- Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
ISO/TR 10358:1993 Plastics pipes and fittings -- Combined chemical-resistance classification table

Tekninen komitea

CEN/TC 155 Plastics piping systems and ducting systems »

Direktiivi

97/23/EC Painelaitteet
2014/68/EU

http://ec.europa.eu »

Vahvistuspäivä

18.04.2006

Julkaisupäivä

05.05.2006

Painos

1

Sivumäärä

38

Julkaisun kieli

englanti