Petroleum and natural gas industries. Design and operation of subsea production systems. Part 11: Flexible pipe systems for subsea and marine applications (ISO 13628-11:2007)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 13628-11:2007 provides guidelines for the design, analysis, manufacture, testing, installation and operation of flexible pipes and flexible pipe systems for onshore, subsea and marine applications. ISO 13628-11:2007 supplements ISO 13628-2 and ISO 13628-10, which specify minimum requirements for the design, material selection, manufacture, testing, marking and packaging of unbonded and bonded flexible pipes, respectively. ISO 13628-11:2007 applies to flexible pipe assemblies, consisting of segments of flexible pipe body with end fittings attached to both ends. Both bonded and unbonded pipe types are covered. In addition, ISO 13628-11:2007 applies to flexible pipe systems, including ancillary components. The applications covered by ISO 13628-11:2007 are sweet- and sour-service production, including export and injection applications. ISO 13628-11:2007 applies to both static and dynamic flexible pipe systems used as flowlines, risers and jumpers. ISO 13628-11:2007 does cover, in general terms, the use of flexible pipes for offshore loading systems. ISO 13628-11:2007 does not cover flexible pipes for use in choke and kill lines or umbilical and control lines.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, abbreviated terms, definitions and symbols
3.1 Terms and definitions
3.2 Symbols and abbreviated terms
4 System, pipe, and component description
4.1 Introduction
4.2 Flexible pipe systems
4.3 Flexible pipe description
4.4 Ancillary components
5 Pipe design considerations
5.1 General
5.2 Design overview
5.3 Failure modes
5.4 Design criteria
5.5 Load cases
6 Materials
6.1 Scope
6.2 Materials — Unbonded pipe
6.3 Materials — Bonded pipe
6.4 Alternative materials
6.5 Polymer/elastomer test procedures
6.6 Metallic-material test requirements
7 System design considerations
7.1 General
7.2 General system requirements
7.3 Flowline design requirements
7.4 Riser design requirements
7.5 Ancillary components
7.6 System interfaces
8 Analysis considerations
8.1 Introduction
8.2 Analysis techniques
8.3 Loads
8.4 Global-response evaluation
9 Prototype testing
9.1 General
9.2 Design programmes
9.3 Classification of prototype tests
9.4 Test requirements
9.5 Test protocol
9.6 Procedures — Standard prototype tests
9.7 Procedures — Special prototype tests
10 Manufacturing
10.1 General
10.2 Manufacturing — Unbonded pipe
10.3 Manufacturing — Bonded pipe
10.4 Marking
10.5 Storage
11 Handling, transportation, and installation
11.1 General
11.2 Handling
11.3 Transportation
11.4 Installation
11.5 Pre-commissioning and commissioning
12 Retrieval and reuse
12.1 General
12.2 Retrieval
12.3 Reuse
13 Integrity and condition monitoring
13.1 General
13.2 General philosophy
13.3 Failure modes and potential pipe defects
13.4 Monitoring methods
13.5 Recommendations
Annex A Flexible-pipe high-temperature end-fitting qualification test protocol — Volatile-content polymers (normative)
Annex B Polyvinylidene fluoride (PVDF) coupon crude-oil exposure-test procedure (normative)
Annex C Flexible-pipe high-temperature end-fitting qualification test procedures: Low-volatile-content polymers (normative)
Annex D Polymer coupon crude-oil exposure-test procedure (normative)
ISO 13628-10:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 10: Specification for bonded flexible pipe
ISO 13628-2:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 2: Unbonded flexible pipe systems for subsea and marine applications
ISO 13628-3:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 3: Through flowline (TFL) systems
ISO 13628-10:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 10: Specification for bonded flexible pipe
ISO 13628-2:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 2: Unbonded flexible pipe systems for subsea and marine applications
ISO 13628-3:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 3: Through flowline (TFL) systems