SFS-EN ISO 13626:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 13626:2003 specifies requirements and gives recommendations for suitable steel structures for drilling and well-servicing operations in the petroleum industry, provides a uniform method of rating the structures, and provides two product specification levels.
ISO 13626:2003 is applicable to all new designs of all standard steel derricks, special steel derricks, portable masts and substructures.
Annex A provides a number of standard supplementary requirements which apply only if specified by the purchaser.

Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Product specification levels
5 Marking and information

5.1 Nameplate
5.2 Derrick and mast nameplate information
5.3 Substructure nameplate information
5.4 Crown block assembly nameplate information (required only for crown block assemblies for use with derricks)

6 Standard ratings

6.1 General
6.2 Derrick (stationary base)
6.3 Mast with guy lines
6.4 Mast without guy lines
6.5 Derrick and mast under dynamic conditions
6.6 Substructure
6.7 Substructure under dynamic conditions
6.8 Crown block assembly

7 Design loading

7.1 General
7.2 Derrick (stationary base)
7.3 Mast with guy lines
7.4 Mast without guy lines
7.5 Derrick and mast under dynamic conditions
7.6 Substructure
7.7 Substructure under dynamic conditions
7.8 Guide tracks and dollies
7.9 Crown block assemblies

8 Design specification

8.1 Allowable stresses
8.2 Wind
8.3 Dynamic loading (induced by floating hull motion)
8.4 Earthquake
8.5 Design verification

9 Materials

9.1 General
9.2 Written specifications
9.3 Mechanical properties
9.4 Material qualification
9.5 Material manufacture
9.6 Bolts
9.7 Wire rope

10 Welding requirements

10.1 General
10.2 Welding qualifications
10.3 Written documentation
10.4 Control of consumables
10.5 Weld properties
10.6 Post-weld heat treatment
10.7 Quality control requirements
10.8 Specific requirement — repair welds

11 Quality control

11.1 General
11.2 Quality control personnel qualifications
11.3 Measuring and test equipment
11.4 Non-destructive examination
11.5 Dimensional verification
11.6 Workmanship and finishing
11.7 Purchaser's inspection and rejection
11.8 Testing
11.9 Traceability

12 Documentation

12.1 General
12.2 Documentation to be kept by the manufacturer
12.3 Documentation to be delivered with equipment

Annex A Supplementary requirements (normative)
Annex B Standard derricks (normative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Product specification levels
5 Marking and information

5.1 Nameplate
5.2 Derrick and mast nameplate information
5.3 Substructure nameplate information
5.4 Crown block assembly nameplate information (required only for crown block assemblies for use with derricks)

6 Standard ratings

6.1 General
6.2 Derrick (stationary base)
6.3 Mast with guy lines
6.4 Mast without guy lines
6.5 Derrick and mast under dynamic conditions
6.6 Substructure
6.7 Substructure under dynamic conditions
6.8 Crown block assembly

7 Design loading

7.1 General
7.2 Derrick (stationary base)
7.3 Mast with guy lines
7.4 Mast without guy lines
7.5 Derrick and mast under dynamic conditions
7.6 Substructure
7.7 Substructure under dynamic conditions
7.8 Guide tracks and dollies
7.9 Crown block assemblies

8 Design specification

8.1 Allowable stresses
8.2 Wind
8.3 Dynamic loading (induced by floating hull motion)
8.4 Earthquake
8.5 Design verification

9 Materials

9.1 General
9.2 Written specifications
9.3 Mechanical properties
9.4 Material qualification
9.5 Material manufacture
9.6 Bolts
9.7 Wire rope

10 Welding requirements

10.1 General
10.2 Welding qualifications
10.3 Written documentation
10.4 Control of consumables
10.5 Weld properties
10.6 Post-weld heat treatment
10.7 Quality control requirements
10.8 Specific requirement — repair welds

11 Quality control

11.1 General
11.2 Quality control personnel qualifications
11.3 Measuring and test equipment
11.4 Non-destructive examination
11.5 Dimensional verification
11.6 Workmanship and finishing
11.7 Purchaser's inspection and rejection
11.8 Testing
11.9 Traceability

12 Documentation

12.1 General
12.2 Documentation to be kept by the manufacturer
12.3 Documentation to be delivered with equipment

Annex A Supplementary requirements (normative)
Annex B Standard derricks (normative)

Bibliography

Tuoteryhmä(t)

75.180.10 Tutkimus-, poraus- ja tuotantolaitteet »

Sidokset

Velvoittavat viittaukset

API RP 2A-WSD:2000
API RP 9B:2011
API SPEC 8A:1997

Tekninen komitea

CEN/TC 12 Oil and gas industries including lower carbon energy »

Vahvistuspäivä

16.05.2005

Julkaisupäivä

03.06.2005

Painos

1

Sivumäärä

35

Julkaisun kieli

englanti