ISO 13628-6:2006 is applicable to design, fabrication, testing, installation and operation of subsea production control systems. ISO 13628-6:2006 covers surface control system equipment, subsea-installed control system equipment and control fluids. This equipment is utilized for control of subsea production of oil and gas and for subsea water and gas injection services. Where applicable, ISO 13628-6:2006 can be used for equipment on multiple-well applications. ISO 13628-6:2006 establishes design standards for systems, subsystems, components and operating fluids in order to provide for the safe and functional control of subsea production equipment. ISO 13628-6:2006 contains various types of information related to subsea production control systems. They are informative data that provide an overview of the architecture and general functionality of control systems for the purpose of introduction and information; basic prescriptive data that shall be adhered to by all types of control system; selective prescriptive data that are control-system-type sensitive and shall be adhered to only when they are relevant; optional data or requirements that need be adopted only when considered necessary either by the purchaser or the vendor. In view of the diverse nature of the data provided, control system purchasers and specifiers are advised to select from ISO 13628-6:2006 only the provisions needed for the application at hand. Failure to adopt a selective approach to the provisions contained herein can lead to overspecification and higher purchase costs. Rework and repair of used equipment are beyond the scope of ISO 13628-6:2006.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviated terms
5 System requirements
5.1 General
5.2 Concept development
5.3 Production control system functionality requirement
5.4 General requirements
5.5 Functional requirements
5.6 Design requirements
6 Surface equipment
6.1 General
6.2 General requirements
6.3 Functional requirements
6.4 Design requirements
7 Subsea equipment
7.1 General
7.2 General requirements
7.3 Functional requirements
7.4 Design requirements
8 Interfaces
8.1 General
8.2 Interface to host facility
8.3 Interface to subsea equipment
8.4 Interface to workover control system
8.5 Interface to intelligent wells
9 Materials and fabrication
9.1 General
9.2 Materials
9.3 Fabrication
10 Quality
11 Testing
11.1 General
11.2 Qualification testing
11.3 Factory acceptance tests (FAT)
11.4 Integrated system tests
11.5 Documentation
12 Marking, packaging, storage and shipping
12.1 Marking
12.2 Packaging
12.3 Storage and shipping
Annex A Types and selection of control system (informative)
Annex B Typical control and monitoring functions (informative)
Annex C Properties and testing of control fluids (informative)
Annex D Operational considerations with respect to flowline pressure exposure (informative)
Annex E Interface to intelligent well (normative)
Annex F Definition of subsea electromagnetic environment and guidance on the selection of tests, limits and severity to provide a presumption of compliance of subsea equipment (informative)
5.3 Production control system functionality requirement
5.4 General requirements
5.5 Functional requirements
5.6 Design requirements
6 Surface equipment
6.1 General
6.2 General requirements
6.3 Functional requirements
6.4 Design requirements
7 Subsea equipment
7.1 General
7.2 General requirements
7.3 Functional requirements
7.4 Design requirements
8 Interfaces
8.1 General
8.2 Interface to host facility
8.3 Interface to subsea equipment
8.4 Interface to workover control system
8.5 Interface to intelligent wells
9 Materials and fabrication
9.1 General
9.2 Materials
9.3 Fabrication
10 Quality
11 Testing
11.1 General
11.2 Qualification testing
11.3 Factory acceptance tests (FAT)
11.4 Integrated system tests
11.5 Documentation
12 Marking, packaging, storage and shipping
12.1 Marking
12.2 Packaging
12.3 Storage and shipping
Annex A Types and selection of control system (informative)
Annex B Typical control and monitoring functions (informative)
Annex C Properties and testing of control fluids (informative)
Annex D Operational considerations with respect to flowline pressure exposure (informative)
Annex E Interface to intelligent well (normative)
Annex F Definition of subsea electromagnetic environment and guidance on the selection of tests, limits and severity to provide a presumption of compliance of subsea equipment (informative)
ANSI/ASME B 31.3:2004
ASME BPVC Section 8 Division 1:2004
ASME BPVC Section 9:2004
ASTM D 1141:1998 Standard Practice for the Preparation of Substitute Ocean Water
ASTM D 1298:1999 Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
ASTM D 2625:1994 Standard Test Method for Endurance (Wear) Life and Load-Carrying Capacity of Solid Film Lubricants (Falex Pin and Vee Method)
ASTM D 2670:1995 Standard Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method)
ASTM D 3233:1993 Standard Test Methods for Measurement of Extreme Pressure Properties of Fluid Lubricants (Falex Pin and Vee Block Methods)
ASTM D 445:2004 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 471:1998 Standard Test Method for Rubber Property—Effect of Liquids
ASTM D 665:2003 Standard Test Method for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water
ASTM D 892:2005 Standard Test Method for Foaming Characteristics of Lubricating Oils
ASTM D 97:2005 Standard Test Method for Pour Point of Petroleum Products
ASTM G 1:2003 Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
BS 7201-1:1990
DIN 41612-2:1987
IEC 61892-1:2001
IEC 61892-2:2005
IEC 61892-3:1999
IEC 61892-5:2000
IEC 61892-6:1999
IEC 61892-7:1997
ISO 10423:2003 Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment
ISO 10945:1994 Hydraulic fluid power -- Gas-loaded accumulators -- Dimensions of gas ports
ISO 13628-4:1999 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 4: Subsea wellhead and tree equipment
ISO 13628-5:2002 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 5: Subsea umbilicals
ISO 15607:2003 Specification and qualification of welding procedures for metallic materials -- General rules
ISO 15609-2:2001 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 2: Gas welding
ISO 15610:2003 Specification and qualification of welding procedures for metallic materials -- Qualification based on tested welding consumables
ISO 15611:2003 Specification and qualification of welding procedures for metallic materials -- Qualification based on previous welding experience
ISO 15612:2004 Specification and qualification of welding procedures for metallic materials -- Qualification by adoption of a standard welding procedure
ISO 15613:2004 Specification and qualification of welding procedures for metallic materials -- Qualification based on pre-production welding test
ISO 15614-1:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure test -- Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
ISO 3722:1976 Hydraulic fluid power -- Fluid sample containers -- Qualifying and controlling cleaning methods
ISO 4406:1999 Hydraulic fluid power -- Fluids -- Method for coding the level of contamination by solid particles
ISO 7498-2:1989 Information processing systems -- Open Systems Interconnection -- Basic Reference Model -- Part 2: Security Architecture
ISO 9606-1:1994 Approval testing of welders -- Fusion welding -- Part 1: Steels
ISO 9606-2:2004 Qualification test of welders -- Fusion welding -- Part 2: Aluminium and aluminium alloys
ISO/TR 10949:2002 Hydraulic fluid power -- Component cleanliness -- Guidelines for achieving and controlling cleanliness of components from manufacture to installation
ISO/TS 16431:2002 Hydraulic fluid power -- Assembled systems -- Verification of cleanliness