SFS-EN ISO 10407-2:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 10407-2:2008 specifies the required inspection for each level of inspection and procedures for the inspection and testing of used drill-stem elements. For the purpose of ISO 10407-2:2008, drill stem elements include drill pipe body, tool joints, rotary-shouldered connections, drill collar, HWDP and the ends of drill-stem elements that make up with them. ISO 10407-2:2008 has been prepared to address the practices and technology commonly used in inspection.
The practices established within ISO 10407-2:2008 are intended as inspection and/or testing guidance and are not intended to be interpreted to prohibit the agency or owner from using personal judgement, supplementing the inspection with other techniques, extending existing techniques or re-inspecting certain lengths.
ISO 10407-2:2008 specifies the qualification of inspection personnel, a description of inspection methods and apparatus calibration and standardization procedures for various inspection methods. The evaluation of imperfections and the marking of inspected drill stem elements is included.
ISO 10407-2:2008 provides the original equipment manufacturers' requirements regarding the minimum information needed for the inspection of their specialized tools.

Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms

4.1 Symbols
4.2 Abbreviated terms

5 Conformance

5.1 Basis for inspection
5.2 Repeatability of results
5.3 Ordering information

6 Quality assurance

6.1 General
6.2 Standardization and operating procedures
6.3 Equipment description
6.4 Personnel qualification
6.5 Dynamic test data demonstrating the system capabilities for detecting the reference indicators
6.6 Reports

7 Qualification of inspection personnel

7.1 General
7.2 Written procedure
7.3 Qualification responsibility and requirements
7.4 Training programmes
7.5 Examinations
7.6 Experience
7.7 Re-qualification
7.8 Documentation
7.9 NDT personnel certification

8 General inspection procedures

8.1 General
8.2 Owner/operator work site requirements for quality inspection
8.3 Documents at job site
8.4 Pre-inspection procedures
8.5 Drill-pipe and tool-joint classification markings
8.6 Post-inspection procedures

9 General non-destructive inspection method requirements

9.1 General
9.2 Equipment
9.3 Illumination
9.4 Magnetic-particle-inspection equipment
9.5 Ultrasonic
9.6 Electromagnetic inspection units

10 Drill stem element inspection and classification

10.1 Pipe body — Full-length visual inspection
10.2 Drill body — Outside diameter gauging
10.3 Pipe body — Ultrasonic wall-thickness gauging
10.4 Pipe body — Full-length electromagnetic inspection (EMI)
10.5 Pipe body — Full-length ultrasonic transverse and wall thickness
10.6 Pipe body — Full-length ultrasonic transverse, wall thickness and longitudinal inspection
10.7 Drill-pipe body — External magnetic-particle inspection of the critical area
10.8 Drill-pipe body — Bi-directional external magnetic-particle inspection of the critical area
10.9 Pipe body — Full-length wall-loss inspection
10.10 Pipe body — Ultrasonic inspection of the critical area
10.11 Pipe body — Calculation of cross-sectional area
10.12 Pipe body — Document review (traceability)
10.13 Pipe body — Evaluation and classification
10.14 Tool joints
10.15 Tool joints — Check for box swell and pin stretch
10.16 Repair of rejected tool joints
10.17 Tool joints — Check tool-joint pin and box outside diameter and eccentric wear
10.18 Tool joints — Measure tool-joint pin and box outside diameter and check for eccentric wear
10.19 Tool joints — Check tool-joint pin and box tong space
10.20 Tool joints — Measure tool-joint pin and box tong space
10.21 Tool joint — Magnetic-particle inspection of the pin threads
10.22 Tool joint — Magnetic-particle inspection of box threads
10.23 Tool joints — Measure tool-joint pin inside diameter
10.24 Magnetic-particle inspection of the connection OD for heat-check cracking
10.25 Bi-directional wet magnetic-particle inspection of the connection OD for heat-check cracking
10.26 Tool joints — Measure the tool-joint counterbore depth, pin-base length and seal width
10.27 BHA connection — Visual inspection of bevels, seals, threads and stress-relief features
10.28 BHA - Measure box outside diameter, pin inside diameter, counterbore diameter and benchmark location if a benchmark is present
10.29 BHA — Check bevel diameter
10.30 BHA — Measure bevel diameter
10.31 BHA — Magnetic-particle inspection of the pin and box threads
10.32 BHA connection — Liquid-penetrant inspection of the pin and box threads
10.33 BHA — Dimensional measurement of stress-relief features
10.34 Length measurements of the counterbore, pin and pin neck
10.35 Drill collar — Visual full-length OD and ID, markings, fish-neck length and tong space
10.36 Drill-collar elevator groove and slip-recess magnetic-particle inspection
10.37 Drill-collar elevator-groove and slip-recess measurement
10.38 Subs (full-length visual OD and ID), fish-neck length, section-change radius and markings
10.39 Float-bore recess measurements
10.40 Magnetic-particle inspection of subs — Full-length, internal and external
10.41 HWDP — Visual full-length OD and ID, markings and tong space
10.42 Visual inspection and wear pattern report for kelly
10.43 Magnetic-particle evaluation of critical areas on kellys
10.44 Magnetic-particle evaluation, full length, of the drive section on kellys
10.45 Stabilizer (full-length visual OD and ID), fish-neck length, blade condition, ring gauge and markings
10.46 Magnetic-particle inspection of the base of stabilizer blades for cracking
10.47 Function test
10.48 Bi-directional, wet magnetic-particle inspection of the base of stabilizer blade for cracking
10.49 Visual inspection of jars (drilling and fishing), accelerators and shock subs
10.50 Maintenance review
10.51 Dimensional measurement of wear areas as specified by OEM requirements
10.52 Original equipment manufacturer designated testing for used equipment
10.53 MWD/LWD — Visual, full-length OD and ID, and markings, including visual inspection of hard-banding and coatings
10.54 Motors and turbines — Visual, full-length OD and ID and markings, including visual inspection of hard-banding and coatings
10.55 Reamers, scrapers, and hole openers — Visual, full-length OD and ID and markings, including visual inspection of hard-banding and coatings
10.56 Rotary steerable — Visual, full-length OD and ID and markings, including visual inspection of hard-banding
10.57 Full-length drift
10.58 Proprietary equipment inspection
10.59 Hard-banding inspection
10.60 Transverse magnetic-particle inspection of tool-joint OD and ID under the pin threads
10.61 Drill-pipe body — Internal magnetic-particle inspection of the critical area
10.62 Drill-pipe body — Bi-directional, internal magnetic-particle inspection of the critical area
10.63 API external upset-thread connection inspection

Annex A Original equipment manufacturer (OEM) requirements (normative)
Annex B Required and additional inspections by product and class of service (normative)
Annex C SI units (normative)
Annex D USC units (informative)
Annex E Inspection-level guidelines (informative)
Annex F Proprietary drill stem connection inspection (informative)
Annex G Used work-string tubing proprietary-connection thread inspection (informative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms

4.1 Symbols
4.2 Abbreviated terms

5 Conformance

5.1 Basis for inspection
5.2 Repeatability of results
5.3 Ordering information

6 Quality assurance

6.1 General
6.2 Standardization and operating procedures
6.3 Equipment description
6.4 Personnel qualification
6.5 Dynamic test data demonstrating the system capabilities for detecting the reference indicators
6.6 Reports

7 Qualification of inspection personnel

7.1 General
7.2 Written procedure
7.3 Qualification responsibility and requirements
7.4 Training programmes
7.5 Examinations
7.6 Experience
7.7 Re-qualification
7.8 Documentation
7.9 NDT personnel certification

8 General inspection procedures

8.1 General
8.2 Owner/operator work site requirements for quality inspection
8.3 Documents at job site
8.4 Pre-inspection procedures
8.5 Drill-pipe and tool-joint classification markings
8.6 Post-inspection procedures

9 General non-destructive inspection method requirements

9.1 General
9.2 Equipment
9.3 Illumination
9.4 Magnetic-particle-inspection equipment
9.5 Ultrasonic
9.6 Electromagnetic inspection units

10 Drill stem element inspection and classification

10.1 Pipe body — Full-length visual inspection
10.2 Drill body — Outside diameter gauging
10.3 Pipe body — Ultrasonic wall-thickness gauging
10.4 Pipe body — Full-length electromagnetic inspection (EMI)
10.5 Pipe body — Full-length ultrasonic transverse and wall thickness
10.6 Pipe body — Full-length ultrasonic transverse, wall thickness and longitudinal inspection
10.7 Drill-pipe body — External magnetic-particle inspection of the critical area
10.8 Drill-pipe body — Bi-directional external magnetic-particle inspection of the critical area
10.9 Pipe body — Full-length wall-loss inspection
10.10 Pipe body — Ultrasonic inspection of the critical area
10.11 Pipe body — Calculation of cross-sectional area
10.12 Pipe body — Document review (traceability)
10.13 Pipe body — Evaluation and classification
10.14 Tool joints
10.15 Tool joints — Check for box swell and pin stretch
10.16 Repair of rejected tool joints
10.17 Tool joints — Check tool-joint pin and box outside diameter and eccentric wear
10.18 Tool joints — Measure tool-joint pin and box outside diameter and check for eccentric wear
10.19 Tool joints — Check tool-joint pin and box tong space
10.20 Tool joints — Measure tool-joint pin and box tong space
10.21 Tool joint — Magnetic-particle inspection of the pin threads
10.22 Tool joint — Magnetic-particle inspection of box threads
10.23 Tool joints — Measure tool-joint pin inside diameter
10.24 Magnetic-particle inspection of the connection OD for heat-check cracking
10.25 Bi-directional wet magnetic-particle inspection of the connection OD for heat-check cracking
10.26 Tool joints — Measure the tool-joint counterbore depth, pin-base length and seal width
10.27 BHA connection — Visual inspection of bevels, seals, threads and stress-relief features
10.28 BHA - Measure box outside diameter, pin inside diameter, counterbore diameter and benchmark location if a benchmark is present
10.29 BHA — Check bevel diameter
10.30 BHA — Measure bevel diameter
10.31 BHA — Magnetic-particle inspection of the pin and box threads
10.32 BHA connection — Liquid-penetrant inspection of the pin and box threads
10.33 BHA — Dimensional measurement of stress-relief features
10.34 Length measurements of the counterbore, pin and pin neck
10.35 Drill collar — Visual full-length OD and ID, markings, fish-neck length and tong space
10.36 Drill-collar elevator groove and slip-recess magnetic-particle inspection
10.37 Drill-collar elevator-groove and slip-recess measurement
10.38 Subs (full-length visual OD and ID), fish-neck length, section-change radius and markings
10.39 Float-bore recess measurements
10.40 Magnetic-particle inspection of subs — Full-length, internal and external
10.41 HWDP — Visual full-length OD and ID, markings and tong space
10.42 Visual inspection and wear pattern report for kelly
10.43 Magnetic-particle evaluation of critical areas on kellys
10.44 Magnetic-particle evaluation, full length, of the drive section on kellys
10.45 Stabilizer (full-length visual OD and ID), fish-neck length, blade condition, ring gauge and markings
10.46 Magnetic-particle inspection of the base of stabilizer blades for cracking
10.47 Function test
10.48 Bi-directional, wet magnetic-particle inspection of the base of stabilizer blade for cracking
10.49 Visual inspection of jars (drilling and fishing), accelerators and shock subs
10.50 Maintenance review
10.51 Dimensional measurement of wear areas as specified by OEM requirements
10.52 Original equipment manufacturer designated testing for used equipment
10.53 MWD/LWD — Visual, full-length OD and ID, and markings, including visual inspection of hard-banding and coatings
10.54 Motors and turbines — Visual, full-length OD and ID and markings, including visual inspection of hard-banding and coatings
10.55 Reamers, scrapers, and hole openers — Visual, full-length OD and ID and markings, including visual inspection of hard-banding and coatings
10.56 Rotary steerable — Visual, full-length OD and ID and markings, including visual inspection of hard-banding
10.57 Full-length drift
10.58 Proprietary equipment inspection
10.59 Hard-banding inspection
10.60 Transverse magnetic-particle inspection of tool-joint OD and ID under the pin threads
10.61 Drill-pipe body — Internal magnetic-particle inspection of the critical area
10.62 Drill-pipe body — Bi-directional, internal magnetic-particle inspection of the critical area
10.63 API external upset-thread connection inspection

Annex A Original equipment manufacturer (OEM) requirements (normative)
Annex B Required and additional inspections by product and class of service (normative)
Annex C SI units (normative)
Annex D USC units (informative)
Annex E Inspection-level guidelines (informative)
Annex F Proprietary drill stem connection inspection (informative)
Annex G Used work-string tubing proprietary-connection thread inspection (informative)

Bibliography

Tuoteryhmä(t)

75.180.10 Tutkimus-, poraus- ja tuotantolaitteet »

Sidokset

Velvoittavat viittaukset

API RP 7A 1:1992
ISO 10424-1:2004 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements
ISO 11961:1996 Petroleum and natural gas industries -- Steel pipes for use as drill pipe -- Specification

Tekninen komitea

CEN/TC 12 Oil and gas industries including lower carbon energy »

Vahvistuspäivä

25.05.2009

Julkaisupäivä

12.06.2009

Painos

1

Sivumäärä

217

Julkaisun kieli

englanti