Verkkokauppa
SFS-EN ISO 14530-1:en
Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs). Part 1: Designation system and basis for specifications (ISO 14530-1:1999)
Soveltamisala
Suomenkielistä soveltamisalaa ei ole saatavissa.
1.1 This part of ISO 14530 establishes a data block system for the designation of unsaturated-polyester powder
moulding compounds (UP-PMCs).
1.2 The various types of UP-PMC are differentiated from each other by a classification system based on
information about the filler/reinforcement type and content, the intended method of processing, any special
properties and those of the special properties used specifically for designation purposes (designatory properties).
1.3 This part of ISO 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or
ground material.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 14530 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 14530-2, if suitable.
1.5 Whenever general requirement data, as covered by ISO 14530-3, need to be indicated, this is also done
using this data block system.
1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the
system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
1.1 This part of ISO 14530 establishes a data block system for the designation of unsaturated-polyester powder
moulding compounds (UP-PMCs).
1.2 The various types of UP-PMC are differentiated from each other by a classification system based on
information about the filler/reinforcement type and content, the intended method of processing, any special
properties and those of the special properties used specifically for designation purposes (designatory properties).
1.3 This part of ISO 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or
ground material.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 14530 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 14530-2, if suitable.
1.5 Whenever general requirement data, as covered by ISO 14530-3, need to be indicated, this is also done
using this data block system.
1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the
system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
Sisällysluettelo
Tuoteryhmä(t)
Sidokset
Velvoittavat viittaukset
ISO 1043-1:1997 Plastics -- Symbols and abbreviated terms -- Part 1: Basic polymers and their special characteristics
ISO 1043-2:2011 Plastics -- Symbols and abbreviated terms -- Part 2: Fillers and reinforcing materials
ISO 14530-2:1999 Plastics -- Unsaturated-polyester powder moulding compounds (UP-PMCs) -- Part 2: Preparation of test specimens and determination of properties
ISO 1043-2:2011 Plastics -- Symbols and abbreviated terms -- Part 2: Fillers and reinforcing materials
ISO 14530-2:1999 Plastics -- Unsaturated-polyester powder moulding compounds (UP-PMCs) -- Part 2: Preparation of test specimens and determination of properties
Tekninen komitea
Vahvistuspäivä
27.03.2000
Julkaisupäivä
03.07.2002
Painos
1
Sivumäärä
12
Julkaisun kieli
englanti