SFS-EN ISO 15085:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 15085:2003 specifies the design as well as the construction and strength requirements for safety devices and arrangements intended to minimize the risk of falling overboard, and requirements to facilitate reboarding.
It describes means which can be used individually or combined to achieve these objectives, and applies to small craft of up to 24 m length of hull.
ISO 15085:2003 is not applicable to the following boat types:
aquatic toys;canoes, kayaks, or other boats with a beam less than 1,1 m;personal watercraft, covered by ISO 13590;inflatable boats with a hull length of less than 8 m, covered by ISO 6185.

Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements

4.1 Functions of the working deck
4.2 Means of protection
4.3 Minimum width of decks
4.4 Continuity of the working deck

5 Safety devices
6 Tables of requirements

6.1 General
6.2 Requirements for non-sailing boats
6.3 Requirements for sailing boats

7 Specific requirement for slip-resistant areas

7.1 General
7.2 Requirements for trampolines and nets

8 Requirements for foot-stops

8.1 General
8.2 Provision of foot-stops
8.3 Minimum foot-stop height and angle
8.4 Foot-stops made of angled surfaces
8.5 Maximum foot-stop clearance between deck and foot stop
8.6 Continuity on the working deck level in way of the foot-stop
8.7 Gaps in the foot-stop rail

9 Requirements for handholds

9.1 General
9.2 Location in way of side decks
9.3 Strength

10 Common requirements for low and high guard-rails and guard-lines

10.1 General
10.2 Height of guard-rails or guard-lines
10.3 Intermediate lines, vertical spacing and maximum gap
10.4 Risk of falling overboard from elevated parts
10.5 Openings in guard-rails/guard-lines
10.6 Bow pulpits for sailing boats
10.7 Transom guard-rails/guard-lines for sailing boats
10.8 Forward cross beams of sailing catamarans
10.9 Central hull of sailing trimarans

11 Specific strength requirements for guard-rails or low guard-rails
12 Specific requirements for guard-lines

12.1 Requirements for high guard-lines, low guard-lines and intermediate guard-lines
12.2 Requirements for stanchions or guard-line supports

13 Requirements for hooking points

13.1 General
13.2 Location
13.3 Size
13.4 Strength

14 Attachment points for jack-lines

14.1 General
14.2 Fitting
14.3 Strength

15 Body support on high-speedboats

15.1 General
15.2 Body support

16 Means of reboarding
17 Owner's manual

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements

4.1 Functions of the working deck
4.2 Means of protection
4.3 Minimum width of decks
4.4 Continuity of the working deck

5 Safety devices
6 Tables of requirements

6.1 General
6.2 Requirements for non-sailing boats
6.3 Requirements for sailing boats

7 Specific requirement for slip-resistant areas

7.1 General
7.2 Requirements for trampolines and nets

8 Requirements for foot-stops

8.1 General
8.2 Provision of foot-stops
8.3 Minimum foot-stop height and angle
8.4 Foot-stops made of angled surfaces
8.5 Maximum foot-stop clearance between deck and foot stop
8.6 Continuity on the working deck level in way of the foot-stop
8.7 Gaps in the foot-stop rail

9 Requirements for handholds

9.1 General
9.2 Location in way of side decks
9.3 Strength

10 Common requirements for low and high guard-rails and guard-lines

10.1 General
10.2 Height of guard-rails or guard-lines
10.3 Intermediate lines, vertical spacing and maximum gap
10.4 Risk of falling overboard from elevated parts
10.5 Openings in guard-rails/guard-lines
10.6 Bow pulpits for sailing boats
10.7 Transom guard-rails/guard-lines for sailing boats
10.8 Forward cross beams of sailing catamarans
10.9 Central hull of sailing trimarans

11 Specific strength requirements for guard-rails or low guard-rails
12 Specific requirements for guard-lines

12.1 Requirements for high guard-lines, low guard-lines and intermediate guard-lines
12.2 Requirements for stanchions or guard-line supports

13 Requirements for hooking points

13.1 General
13.2 Location
13.3 Size
13.4 Strength

14 Attachment points for jack-lines

14.1 General
14.2 Fitting
14.3 Strength

15 Body support on high-speedboats

15.1 General
15.2 Body support

16 Means of reboarding
17 Owner's manual

Bibliography

Tuoteryhmä(t)

47.080 Veneet »

Sidokset

Velvoittavat viittaukset

ISO 12217-1:2002 Small craft -- Stability and buoyancy assessment and categorization -- Part 1: Non-sailing boats of hull length greater than or equal to 6 m
ISO 12217-2:2002 Small craft -- Stability and buoyancy assessment and categorization -- Part 2: Sailing boats of hull length greater than or equal to 6 m
ISO 12217-3:2002 Small craft -- Stability and buoyancy assessment and categorization -- Part 3: Boats of hull length less than 6 m

Tekninen komitea

CEN/TC 464 Small Craft »

Direktiivi

94/25/EC Huviveneet ja vapaa-ajan alukset
2003/44/EC Huviveneitä koskevien jäsenvaltioiden lakien, asetusten ja hallinnollisten määräysten lähentämisestä annetun direktiivin 94/25/EY muuttamisesta
2013/53/EU

http://ec.europa.eu »

Vahvistuspäivä

10.11.2003

Julkaisupäivä

28.11.2003

Painos

1

Sivumäärä

26

Julkaisun kieli

englanti