This part of ISO 15252 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of epoxy powder moulding compounds (EP-PMCs). Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PMCs are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, PMCs are also included in this part of ISO 15252, as are the designatory properties found in ISO 15252-1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
IEC 60093:1980
IEC 60112:1979
IEC 60167:1964
IEC 60243-1:1998
IEC 60250:1969
IEC 60296:1982
IEC 60695-11-10:1999
IEC 60695-11-20:1999
IEC 60707:1999
ISO 10350-1:1998 Plastics -- Acquisition and presentation of comparable single-point data -- Part 1: Moulding materials
ISO 10724-1:1998 Plastics -- Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) -- Part 1: General principles and moulding of multipurpose test specimens
ISO 10724-2:1998 Plastics -- Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) -- Part 2: Small plates
ISO 11359-2:1999 Plastics -- Thermomechanical analysis (TMA) -- Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 1183:1987 Plastics -- Methods for determining the density and relative density of non-cellular plastics
ISO 120:1977 Plastics -- Phenol-formaldehyde mouldings -- Determination of free ammonia and ammonium compounds -- Colorimetric comparison method
ISO 14530-1:1999 Plastics -- Unsaturated-polyester powder moulding compounds (UP-PMCs) -- Part 1: Designation system and basis for specifications
ISO 14530-3:1999 Plastics -- Unsaturated-polyester powder moulding compounds (UP-PMCs) -- Part 3: Requirements for selected moulding compounds
ISO 15062 Plastics -- Determination of the thermal-flow and cure behaviour of thermosetting materials by torque rheometry
ISO 171:1980 Plastics -- Determination of bulk factor of moulding materials
ISO 178:1993 Plastics -- Determination of flexural properties
ISO 179-1:2010 Plastics -- Determination of Charpy impact properties -- Part 1: Non-instrumented impact test
ISO 2039-1:1993 Plastics -- Determination of hardness -- Part 1: Ball indentation method
ISO 2577:1984 Plastics -- Thermosetting moulding materials -- Determination of shrinkage
ISO 2818:1994 Plastics -- Preparation of test specimens by machining
ISO 291:1997 Plastics -- Standard atmospheres for conditioning and testing
ISO 295:2004 Plastics -- Compression moulding of test specimens of thermosetting materials
ISO 3167:1993 Plastics -- Multipurpose test specimens
ISO 3671:1976 Plastics -- Aminoplastic moulding materials -- Determination of volatile matter
ISO 4589-2:1996 Plastics -- Determination of burning behaviour by oxygen index -- Part 2: Ambient-temperature test
ISO 4614:1977 Plastics -- Melamine-formaldehyde mouldings -- Determination of extractable formaldehyde
ISO 472:1999 Plastics -- Vocabulary
ISO 527-1:1993 Plastics -- Determination of tensile properties -- Part 1: General principles
ISO 527-2:1993 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics
ISO 60:1977 Plastics -- Determination of apparent density of material that can be poured from a specified funnel
ISO 62:1999 Plastics -- Determination of water absorption
ISO 6603-2:1989 Plastics -- Determination of multiaxial impact behaviour of rigid plastics -- Part 2: Instrumented puncture test
ISO 75-2:1993 Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite
ISO 7808:1992 Plastics -- Thermosetting moulding materials -- Determination of transfer flow
ISO 8256:1990 Plastics -- Determination of tensile-impact strength
ISO 899-1:1993 Plastics -- Determination of creep behaviour -- Part 1: Tensile creep