SFS-EN ISO 18246:2023:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

This document specifies safety requirements for conductive connection of electrically propelled mopeds and motorcycles (referred to as the EVs) to external electric circuits.
NOTE 1   External electric circuits include external electric power supplies and external electric loads.
It does not provide comprehensive safety information for manufacturing, maintenance and repair personnel.
It applies only to on-board charging systems between the plug or vehicle inlet and RESS circuits.
NOTE 2   The requirements when not connected to external electric circuits are specified in the ISO 13063 series.
Requirements for bidirectional energy transfer DC to AC are under consideration and are not part of this document.
NOTE 3   The safety requirements for DC EV supply equipment where protection relies on electrical separation are specified in IEC 61851-25.
NOTE 4   The safety requirements for DC EV supply equipment where protection relies on double or reinforced insulation are specified in IEC TS 61851-3-1 and IEC TS 61851-3-2.

Tämän julkaisun valmistelusta Suomessa vastaa Yhteinen Toimialaliitto, www.ytl.fi.

Sisällysluettelo

Tuoteryhmä(t)

43.140 Moottoripyörät ja mopedit »

Sidokset

Velvoittavat viittaukset

IEC 60664-1 Corrigendum 1:2020
IEC 60664-1:2020 Insulation coordination for equipment within low-voltage supply systems - Part 1: Principles, requirements and tests
IEC 60664-3 Edition 2.1:2010

IEC 60664-1 Corrigendum 1:2020
IEC 60664-1:2020 Insulation coordination for equipment within low-voltage supply systems - Part 1: Principles, requirements and tests
IEC 60664-3 Edition 2.1:2010
IEC 60664-3:2016 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
IEC 60664-4:2005 Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
IEC 61851-1:2017 Electric vehicle conductive charging system - Part 1: General requirements
IEC 61851-23:2014 Electric vehicle conductive charging system - Part 23: DC electric vehicle charging station
IEC 61851-25:2020 Electric vehicle conductive charging system - Part 25: DC EV supply equipment where protection relies on electrical separation
IEC 62196-2:2022 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories
IEC 62196-6:2022 Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 6: Dimensional compatibility requirements for DC pin and contact-tube vehicle couplers intended to be used for DC EV supply equipment where protection relies on electrical separation
IEC 69/845/DTS:2022
IEC/TS 62196-4:2022
ISO 13063-3:2022 Electrically propelled mopeds and motorcycles — Safety specifications — Part 3: Electrical safety
ISO 17409:2020 Electrically propelled road vehicles — Conductive power transfer — Safety requirements
ISO 20653:2013 Road vehicles — Degrees of protection (IP code) — Protection of electrical equipment against foreign objects, water and access
ISO 6469-3:2021 Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety
ISO 7010:2019 Graphical symbols — Safety colours and safety signs — Registered safety signs

Tekninen komitea

CEN/TC 301 Road vehicles »

Vahvistuspäivä

14.04.2023

Julkaisupäivä

18.04.2023

Painos

2

Sivumäärä

45

Julkaisun kieli

englanti