ISO 16330:2003 specifies the technical requirements, other than safety and testing, for reciprocating positive displacement pumps and pump units. It applies to pumps which utilize reciprocating motion derived from crankshafts and camshafts and also direct-acting fluid driven pumps. It does not apply to reciprocating positive displacement pumps, nor pumping water, where the whole pump is lubricated with the liquid being pumped.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Information and requirements to be confirmed, agreed and documented
4.1 Purchaser information
4.2 Optional items
4.3 Supplier's Information
5 Fitness for purpose
6 Pump design
6.1 Environmental conditions
6.2 Basic design criteria
6.3 Design of structural and pressure containing parts
6.4 Sealing systems
6.5 Bearing lubrication
6.6 Shafts
6.7 Process inlet and outlet pipe connections
6.8 Draining and venting
6.9 Threaded fasteners
7 Ancillary equipment
7.1 General
7.2 Driver
7.3 Shaft couplings
7.4 Baseplates
7.5 Guarding
7.6 Heating and cooling
7.7 Pressure safety-relief devices
7.8 Pulsation suppression devices
7.9 Speed reduction
7.10 Ancillary pipe connections
8 Noise
9 Installation and maintenance
9.1 General
10 Materials, welding and repairs
10.1 Selection of materials
10.2 Manufacture
10.3 Repairs
11 Surface protection
12 Nameplates and marking
13 Preparation for shipment
13.1 Corrosion protection
13.2 Openings
13.3 Piping, ancillaries and auxiliaries
13.4 Identification
13.5 Installation and or operating instructions
Annex A Data sheet (informative)
Annex B Optional requirements and items to be agreed (normative)
Annex C Operating margins between NPIPA and NPIPR (informative)
Annex D Recommended maximum permissible residual pressure pulsations (informative)
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
EN 12723:2000 Liquid pumps - General terms for pumps and installations - Definitions, quantities, letter symbols and units
EN 809:1998+A1:2009 Pumps and pump units for liquids - Common safety requirements
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
EN 12723:2000 Liquid pumps - General terms for pumps and installations - Definitions, quantities, letter symbols and units
EN 809:1998+A1:2009 Pumps and pump units for liquids - Common safety requirements
EN ISO 15607:2019 Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2019)
EN ISO 15609-1:2019 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2019)
EN ISO 15614-1:2017 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys (ISO 15614-1:2017, Corrected version 2017-10-01)
EN ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
EN ISO 20361:2019 Liquid pumps and pumps units - Noise test code - Grades 2 and 3 of accuracy (ISO 20361:2019)
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
EN ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread (ISO 898-2:2012)
EN ISO 898-2:2022 Fasteners - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes (ISO 898-2:2022)
EN ISO 9606-1:2017 Qualification testing of welders - Fusion welding - Part 1: Steels (ISO 9606-1:2012 including Cor 1:2012 and Cor 2:2013)
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
EN ISO 9934-1:2016 Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016)
ISO 1027:1983 Radiographic image quality indicators for non-destructive testing -- Principles and identification
ISO 10375:1997 Non-destructive testing -- Ultrasonic inspection -- Characterization of search unit and sound field
ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering -- Dimensions, tolerances and verification
ISO 2491:1974 Thin parallel keys and their corresponding keyways (Dimensions in millimetres)
ISO 2492:1974 Thin taper keys with or without gib head and their corresponding keyways (Dimensions in millimetres)
ISO 3117:1977 Tangential keys and keyways
ISO 3453:1984 Non-destructive testing -- Liquid penetrant inspection -- Means of verification
ISO 3912:1977 Woodruff keys and keyways
ISO 4156:1981 Straight cylindrical involute splines -- Metric module, side fit -- Generalities, dimensions and inspection
ISO 6149-1:1993 Connections for fluid power and general use -- Ports and stud ends with ISO 261 threads and O-ring sealing -- Part 1: Ports with O-ring seal in truncated housing
ISO 6149-2:1993 Connections for fluid power and general use -- Ports and stud ends with ISO 261 threads and O-ring sealing -- Part 2: Heavy-duty (S series) stud ends -- Dimensions, design, test methods and requirements
ISO 6149-3:1993 Connections for fluid power and general use -- Ports and stud ends with ISO 261 threads and O-ring sealing -- Part 3: Light-duty (L series) stud ends -- Dimensions, design, test methods and requirements
ISO 6162-1:2002 Hydraulic fluid power -- Flange connectors with split or one-piece flange clamps and metric or inch screws -- Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127
ISO 6162-2:2002 Hydraulic fluid power -- Flange connectors with split or one-piece flange clamps and metric or inch screws -- Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51
ISO 6164:1994 Hydraulic fluid power -- Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
ISO 7005-1:1992 Metallic flanges -- Part 1: Steel flanges
ISO 7005-2:1988 Metallic flanges -- Part 2: Cast iron flanges
ISO 7005-3:1988 Metallic flanges -- Part 3: Copper alloy and composite flanges
ISO/TR 13593:1999 Enclosed gear drives for industrial applications