Geometrical product specifications (GPS). Acceptance and reverification tests for coordinate measuring machines (CMM). Part 2: CMMs used for measuring linear dimensions (ISO 10360-2:2009)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 10360-2:2009 specifies the acceptance tests for verifying the performance of a coordinate measuring machine (CMM) used for measuring linear dimensions as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the CMM. The acceptance and reverification tests given in ISO 10360-2:2009 are applicable only to Cartesian CMMs using contacting probing systems of any type operating in the discrete-point probing mode. ISO 10360-2:2009 does not explicitly apply to non-Cartesian CMMs or CMMs using optical probing. ISO 10360-2:2009 specifies?performance requirements that can be assigned by the manufacturer or the user of a CMM, the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements, rules for proving conformance, and applications for which the acceptance and reverification tests can be used.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Environmental and metrological requirements
5.1 Environmental conditions
5.2 Operating conditions
5.3 Length measurement error, EL
5.4 Repeatability range of the length measurement error, R0
5.5 Workpiece loading effects
6 Acceptance tests and reverification tests
6.1 General
6.2 Principle
6.3 Length measurement error with zero ram axis stylus tip offset, E0
6.4 Repeatability range of the length measurement error, R0
6.5 Length measurement error with ram axis stylus tip offset of 150 mm, E150
6.6 Dual ram CMMs
7 Compliance with specifications
7.1 Acceptance test
7.2 Reverification test
8 Applications
8.1 Acceptance test
8.2 Reverification test
8.3 Interim check
9 Indication in product documentation and data sheets
Annex A Interim check (informative)
Annex B Artefacts that represent a calibrated test length (normative)
Annex C Alignment of gauges (informative)
Annex D Mathematical adjustments to low CTE artefacts (normative)
Annex E Location of the single stylus probing test (informative)
Annex F Relation to the GPS matrix model (informative)
ISO 10360-1:2000 Geometrical Product Specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 1: Vocabulary
ISO 14253-1:1998 Geometrical Product Specifications (GPS) -- Inspection by measurement of workpieces and measuring equipment -- Part 1: Decision rules for proving conformance or non-conformance with specifications
ISO 14660-1:1999 Geometrical Product Specifications (GPS) -- Geometrical features -- Part 1: General terms and definitions
ISO 10360-1:2000 Geometrical Product Specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 1: Vocabulary
ISO 14253-1:1998 Geometrical Product Specifications (GPS) -- Inspection by measurement of workpieces and measuring equipment -- Part 1: Decision rules for proving conformance or non-conformance with specifications
ISO 14660-1:1999 Geometrical Product Specifications (GPS) -- Geometrical features -- Part 1: General terms and definitions
ISO/IEC Guide 99:2007 International vocabulary of metrology -- Basic and general concepts and associated terms (VIM)
ISO/TS 23165:2006 Geometrical product specifications (GPS) -- Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty