SFS-EN ISO 13709:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 13709:2009 specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services.
ISO 13709:2009 is applicable to overhung pumps, between-bearings pumps and vertically-suspended pumps

Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General

4.1 Unit responsibility
4.2 Classification and designation

5 Requirements

5.1 Units
5.2 Statutory requirements
5.3 Requirements

6 Basic design

6.1 General
6.2 Pump types
6.3 Pressure casings
6.4 Nozzles and pressure casing connections
6.5 External nozzle forces and moments
6.6 Rotors
6.7 Wear rings and running clearances
6.8 Mechanical shaft seals
6.9 Dynamics
6.10 Bearings and bearing housings
6.11 Lubrication
6.12 Materials
6.13 Nameplates and rotation arrows

7 Accessories

7.1 Drivers
7.2 Couplings and guards
7.3 Baseplates
7.4 Instrumentation
7.5 Piping and appurtenances
7.6 Special tools

8 Inspection, testing, and preparation for shipment

8.1 General
8.2 Inspection
8.3 Testing
8.4 Preparation for shipment

9 Specific pump types

9.1 Single-stage overhung pumps
9.2 Between-bearings pumps (types BB1, BB2, BB3 and BB5)
9.3 Vertically suspended pumps (types VS1 through VS7)

10 Vendor's data

10.1 General
10.2 Proposals
10.3 Contract data

Annex A Specific speed and suction-specific speed (informative)
Annex B Cooling water and lubrication system schematics (normative)
Annex C Hydraulic power recovery turbines (normative)
Annex D Standard baseplates (normative)
Annex E Inspector's checklist (informative)
Annex F Criteria for piping design (normative)
Annex G Materials class selection guidance (informative)
Annex H Materials and material specifications for pump parts (normative)
Annex I Lateral analysis (normative)
Annex J Determination of residual unbalance (normative)
Annex K Shaft stiffness and bearing system life (informative)
Annex L Vendor drawing and data requirements (informative)
Annex M Test data summary (informative)
Annex N Pump datasheets and electronic data exchange (informative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General

4.1 Unit responsibility
4.2 Classification and designation

5 Requirements

5.1 Units
5.2 Statutory requirements
5.3 Requirements

6 Basic design

6.1 General
6.2 Pump types
6.3 Pressure casings
6.4 Nozzles and pressure casing connections
6.5 External nozzle forces and moments
6.6 Rotors
6.7 Wear rings and running clearances
6.8 Mechanical shaft seals
6.9 Dynamics
6.10 Bearings and bearing housings
6.11 Lubrication
6.12 Materials
6.13 Nameplates and rotation arrows

7 Accessories

7.1 Drivers
7.2 Couplings and guards
7.3 Baseplates
7.4 Instrumentation
7.5 Piping and appurtenances
7.6 Special tools

8 Inspection, testing, and preparation for shipment

8.1 General
8.2 Inspection
8.3 Testing
8.4 Preparation for shipment

9 Specific pump types

9.1 Single-stage overhung pumps
9.2 Between-bearings pumps (types BB1, BB2, BB3 and BB5)
9.3 Vertically suspended pumps (types VS1 through VS7)

10 Vendor's data

10.1 General
10.2 Proposals
10.3 Contract data

Annex A Specific speed and suction-specific speed (informative)
Annex B Cooling water and lubrication system schematics (normative)
Annex C Hydraulic power recovery turbines (normative)
Annex D Standard baseplates (normative)
Annex E Inspector's checklist (informative)
Annex F Criteria for piping design (normative)
Annex G Materials class selection guidance (informative)
Annex H Materials and material specifications for pump parts (normative)
Annex I Lateral analysis (normative)
Annex J Determination of residual unbalance (normative)
Annex K Shaft stiffness and bearing system life (informative)
Annex L Vendor drawing and data requirements (informative)
Annex M Test data summary (informative)
Annex N Pump datasheets and electronic data exchange (informative)

Bibliography

Tuoteryhmä(t)

23.080 Pumput »
71.120.99 Muut kemiantekniikan laitteet ja varusteet »
75.180.20 Jalostuslaitteet »

Sidokset

Velvoittavat viittaukset

ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements
ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems
ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems

ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements
ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems
ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems
ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 4: Self-acting gas seal support systems
ISO 10441:2007 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- Special-purpose applications
ISO 10721-2:1999 Steel structures -- Part 2: Fabrication and erection
ISO 11342:1998 Mechanical vibration -- Methods and criteria for the mechanical balancing of flexible rotors
ISO 14120:2002 Safety of machinery -- Guards -- General requirements for the design and construction of fixed and movable guards
ISO 14691:2008 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- General-purpose applications
ISO 15156-1:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 1: Arc welding
ISO 15609-1:2004/Cor 1:2005
ISO 15609-2:2001 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 2: Gas welding
ISO 15609-3:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 3: Electron beam welding
ISO 15609-4:2009 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 4: Laser beam welding
ISO 15609-5:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 5: Resistance welding
ISO 15649:2001 Petroleum and natural gas industries -- Piping
ISO 1940-1:2003 Mechanical vibration -- Balance quality requirements for rotors in a constant (rigid) state -- Part 1: Specification and verification of balance tolerances
ISO 21049:2004 Pumps -- Shaft sealing systems for centrifugal and rotary pumps
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 261:1998 ISO general purpose metric screw threads -- General plan
ISO 262:1998 ISO general purpose metric screw threads -- Selected sizes for screws, bolts and nuts
ISO 281:2007 Rolling bearings -- Dynamic load ratings and rating life
ISO 286-1:1988 ISO system of limits and fits -- Part 1: Bases of tolerances, deviations and fits
ISO 286-2 Technical Corrigendum 1:2006
ISO 286-2:1988 ISO system of limits and fits -- Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts
ISO 3117:1977 Tangential keys and keyways
ISO 4200:1991 Plain end steel tubes, welded and seamless -- General tables of dimensions and masses per unit length
ISO 5753:1991 Rolling bearings -- Radial internal clearance
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads -- Part 1: Dimensions, tolerances and designation
ISO 7005-2:1988 Metallic flanges -- Part 2: Cast iron flanges
ISO 724:1993 ISO general-purpose metric screw threads -- Basic dimensions
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 8501-2:1994 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 2: Preparation grades of previously coated steel substrates after localized removal of previous coatings
ISO 8501-3:2006 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 3: Preparation grades of welds, edges and other areas with surface imperfections
ISO 8501-4:2006 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting
ISO 9606-1 AMD 1:1998
ISO 9606-1:1994 Approval testing of welders -- Fusion welding -- Part 1: Steels
ISO 9606-2:2004 Qualification test of welders -- Fusion welding -- Part 2: Aluminium and aluminium alloys
ISO 9606-3:1999 Approval testing of welders -- Fusion welding -- Part 3: Copper and copper alloys
ISO 9606-4:1999 Approval testing of welders -- Fusion welding -- Part 4: Nickel and nickel alloys
ISO 9606-5:2000 Approval testing of welders -- Fusion welding -- Part 5: Titanium and titanium alloys, zirconium and zirconium alloys
ISO 965-1:1998 ISO general-purpose metric screw threads -- Tolerances -- Part 1: Principles and basic data
ISO 965-1:1998/Cor 1:2009
ISO 965-2:1998 ISO general purpose metric screw threads -- Tolerances -- Part 2: Limits of sizes for general purpose external and internal screw threads -- Medium quality
ISO 965-3:1998 ISO general purpose metric screw threads -- Tolerances -- Part 3: Deviations for constructional screw threads
ISO 965-3:1998/Cor 1:2009
ISO 965-4:1998 ISO general purpose metric screw threads -- Tolerances -- Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
ISO 965-5:1998 ISO general purpose metric screw threads -- Tolerances -- Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO 9906:1999 Rotodynamic pumps -- Hydraulic performance acceptance tests -- Grades 1 and 2
ISO/TR 17766:2005 Centrifugal pumps handling viscous liquids -- Performance corrections

Tekninen komitea

CEN/TC 12 Oil and gas industries including lower carbon energy »

Vahvistuspäivä

20.04.2010

Julkaisupäivä

07.05.2010

Painos

2

Sivumäärä

188

Julkaisun kieli

englanti