ISO 13628-15:2011 addresses recommendations for subsea structures and manifolds, within the frameworks set forth by recognized and accepted industry specifications and standards. As such, it does not supersede or eliminate any requirement imposed by any other industry specification. ISO 13628-15:2011 covers subsea manifolds and templates utilized for pressure control in both subsea production of oil and gas, and subsea injection services. The following equipment falls within the scope of ISO 13628-15:2011:
structural components and piping systems of subsea production systems, including
production and injection manifolds, modular and integrated single satellite and multiwell templates, subsea processing and subsea boosting stations, flowline riser bases and export riser bases (FRB, ERB), pipeline end manifolds (PLEM), pipeline end terminations (PLET), T- and Y-connection, and subsea isolation valve (SSIV);
structural components of subsea production system, including
subsea controls and distribution structures and other subsea structures, and protection structures associated with the above.
ISO 13628-15:2011 is not applicable to pipeline and manifold valves, flowline and tie-in connectors, choke valves and production control systems.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
1 Scope
2 Normative references
3 Terms, abbreviated terms, and definitions
3.1 Terms and definitions
3.2 Abbreviated terms
4 Manifold and template functional considerations
4.1 General
4.2 System requirements
4.3 System Interfaces
4.4 Cluster manifold requirements
4.5 Template system requirements
5 Design considerations
5.1 System design
5.2 Loads
5.3 Piping design
5.4 Structural design
5.5 Foundation design
5.6 Components
6 Verification and validation of design
6.1 Design verification
6.2 Design validation
6.3 Other comments
7 Materials and fabrication requirements to piping systems
7.1 General
7.2 Pipe and pipe fittings
7.3 Forged components
7.4 Chemical composition and weldability
7.5 Test sampling of base materials
7.6 Mechanical and corrosion testing of base materials
7.7 Non-destructive inspection of components
7.8 Fastener materials
7.9 Bending and forming operations
7.10 Overlay welding and buttering of components
7.11 Welding and non-destructive testing of piping systems
8 Fabrication and manufacturing considerations
8.1 External corrosion protection
8.2 Colours
8.3 Material traceability
9 Installation, operation and maintenance considerations
ASME B31.3:2010
ASME BPVC Section 5:2007
ASME BPVC Section 8 Division 1:2007
ASME BPVC Section 9:2010
ASTM A 388/A 388M:2011 Standard Practice for Ultrasonic Examination of Steel Forgings
ASTM E 562:2008 Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
ASTM G 48:2003 Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution
EN 10228-3:2016 Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings
EN ISO 14732:2013 Welding personnel - Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials (ISO 14732:2013)
EN ISO 9712:2012 Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012)
EN ISO 9712:2022 Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2021)
ISO 10423:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment
ISO 10474:1991 Steel and steel products -- Inspection documents
ISO 13628-1:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 1: General requirements and recommendations
ISO 13628-1:2005/Amd 1:2010 Revised Clause 6
ISO 13628-4:2010 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 4: Subsea wellhead and tree equipment
ISO 13628-8:2002 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems
ISO 14731:2006 Welding coordination -- Tasks and responsibilities
ISO 15156-1:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials
ISO 15156-2:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 15156-3:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO 15590-1:2009 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 1: Induction bends
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 1: Arc welding
ISO 15609-1:2004/Cor 1:2005
ISO 15609-2:2001 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 2: Gas welding
ISO 15609-3:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 3: Electron beam welding
ISO 15609-4:2009 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 4: Laser beam welding
ISO 15609-5:2004 Specification and qualification of welding procedures for metallic materials -- Welding procedure specification -- Part 5: Resistance welding
ISO 15616-1:2003 Acceptance tests for CO2-laser beam machines for high quality welding and cutting -- Part 1: General principles, acceptance conditions
ISO 15616-2:2003 Acceptance tests for CO2-laser beam machines for high quality welding and cutting -- Part 2: Measurement of static and dynamic accuracy
ISO 15616-3:2003 Acceptance tests for CO2-laser beam machines for high quality welding and cutting -- Part 3: Calibration of instruments for measurement of gas flow and pressure
ISO 15616-4:2008 Acceptance tests for CO2-laser beam machines for high quality welding and cutting -- Part 4: Machines with 2-D moving optics
ISO 3183:2007 Petroleum and natural gas industries -- Steel pipe for pipeline transportation systems
ISO 3834-2:2005 Quality requirements for fusion welding of metallic materials -- Part 2: Comprehensive quality requirements
ISO 9606-1 AMD 1:1998
ISO 9606-1:1994 Approval testing of welders -- Fusion welding -- Part 1: Steels
ISO 9606-2:2004 Qualification test of welders -- Fusion welding -- Part 2: Aluminium and aluminium alloys
ISO 9606-3:1999 Approval testing of welders -- Fusion welding -- Part 3: Copper and copper alloys
ISO 9606-4:1999 Approval testing of welders -- Fusion welding -- Part 4: Nickel and nickel alloys
ISO 9606-5:2000 Approval testing of welders -- Fusion welding -- Part 5: Titanium and titanium alloys, zirconium and zirconium alloys
ISO 9712:2005 Non-destructive testing -- Qualification and certification of personnel