ISO 13706:2011 gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of air-cooled heat exchangers for use in the petroleum, petrochemical and natural gas industries. ISO 13706:2011 is applicable to air-cooled heat exchangers with horizontal bundles, but the basic concepts can also be applied to other configurations.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Proposals
6 Documentation
6.1 Approval information
6.2 Final records
7 Design
7.1 Tube bundle design
7.2 Air-side design
7.3 Structural design
8 Materials
8.1 General
8.2 Requirements for carbon steel in sour or wet hydrogen sulfide service
8.3 Headers
8.4 Louvres
8.5 Other components
9 Fabrication of tube bundle
9.1 Welding
9.2 Postweld heat treatment
9.3 Tube-to-tubesheet joints
9.4 Gasket contact surfaces
9.5 Thread lubrication
9.6 Alignment and tolerances
9.7 Assembly
10 Inspection, examination and testing
10.1 Quality control
10.2 Pressure test
10.3 Shop run-in
10.4 Equipment performance testing
10.5 Nameplates
11 Preparation for shipment
11.1 General
11.2 Surfaces and finishes
11.3 Identification and notification
12 Supplemental requirements
12.1 General
12.2 Design
12.3 Examination
12.4 Testing
Annex A Recommended practices (informative)
Annex B Checklist and data sheets (informative)
Annex C Winterization of air-cooled heat exchangers (informative)
Annex D Recommended procedure for airflow measurement of air-cooled heat exchangers (informative)
Annex E Measurement of noise from air-cooled heat exchangers (informative)
ANSI/AGMA 6001-E:2008
ANSI/AGMA 6010-F:1997
ASME PTC 30:1991
ISO 1081:1995 Belt drives -- V-belts and V-ribbed belts, and corresponding grooved pulleys -- Vocabulary
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles -- Specifications and test methods
ISO 15156-1:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials
ISO 15156-2:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 15156-3:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO 2491:1974 Thin parallel keys and their corresponding keyways (Dimensions in millimetres)
ISO 281:2007 Rolling bearings -- Dynamic load ratings and rating life
ISO 286-1:2010 Geometrical product specifications (GPS) -- ISO code system for tolerances on linear sizes -- Part 1: Basis of tolerances, deviations and fits
ISO 286-2:2010 Geometrical product specifications (GPS) -- ISO code system for tolerances on linear sizes -- Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 4183:1995 Belt drives -- Classical and narrow V-belts -- Grooved pulleys (system based on datum width)
ISO 4184:1992 Belt drives -- Classical and narrow V-belts -- Lengths in datum system
ISO 5287:2003 Belt drives -- Narrow V-belts for the automotive industry -- Fatigue test
ISO 5290:2001 Belt drives -- Grooved pulleys for joined narrow V-belts -- Groove sections 9N/J, 15N/J and 25N/J (effective system)
ISO 76:2006 Rolling bearings -- Static load ratings
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 9563:1990 Belt drives -- Electrical conductivity of antistatic endless synchronous belts -- Characteristics and test method
NACE MR 0103:2007
NACE SP 0472:2010