SFS-EN ISO 13705:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 13705:2012 specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing, preparation for shipment, and erection of fired heaters, air heaters, fans and burners for general refinery service.
ISO 13705:2012 is not intended to apply to the design of steam reformers or pyrolysis furnaces.

Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, abbreviated terms and symbols

3.1 Terms and definitions
3.2 Abbreviated terms and symbols

4 General

4.1 Pressure design code
4.2 Regulations
4.3 Heater nomenclature

5 Proposals

5.1 Purchaser's responsibilities
5.2 Vendor's responsibilities
5.3 Documentation
5.4 Final reports

6 Design considerations

6.1 Process design
6.2 Combustion design
6.3 Mechanical design

7 Tubes

7.1 General
7.2 Extended surface
7.3 Materials

8 Headers

8.1 General
8.2 Plug headers
8.3 Return bends
8.4 Materials

9 Piping, terminals and manifolds

9.1 General
9.2 Allowable movement and loads
9.3 Materials

10 Tube suppports

10.1 General
10.2 Loads and allowable stress
10.3 Materials

11 Refractories and insulation

11.1 General
11.2 Brick and tile construction
11.3 Castable construction
11.4 Ceramic-fibre construction
11.5 Multi-component lining construction
11.6 Materials

12 Structures and appurtenances

12.1 General
12.2 Structures
12.3 Header boxes, doors and ports
12.4 Ladders, platforms and stairways
12.5 Materials

13 Stacks, ducts and breeching

13.1 General
13.2 Design considerations
13.3 Design methods
13.4 Static design
13.5 Wind-induced vibration design
13.6 Materials

14 Burners and auxiliary equipment

14.1 Burners
14.2 Sootblowers
14.3 Fans and drivers
14.4 Dampers and damper controls for stacks and ducts

15 Instrument and auxiliary connections

15.1 Flue gas and air
15.2 Process fluid temperature
15.3 Auxiliary connections
15.4 Tube-skin thermocouples
15.5 Access to connections

16 Shop fabrication and field erection

16.1 General
16.2 Structural-steel fabrication
16.3 Coil fabrication
16.4 Painting and galvanizing
16.5 Refractories and insulation
16.6 Preparation for shipment
16.7 Field erection

17 Inspection, examination and testing

17.1 General
17.2 Weld examination
17.3 Castings examination
17.4 Examination of other components
17.5 Testing

Annex A Equipment data sheets (informative)
Annex B Purchaser's checklist (informative)
Annex C Proposed shop-assembly conditions (informative)
Annex D Stress curves for use in the design of tube-support elements (normative)
Annex E Centrifugal fans for fired-heater systems (normative)
Annex F Air preheat systems for fired process heaters (normative)
Annex G Measurement of efficiency of fired process heaters (informative)
Annex H Stack design (informative)
Annex I Measurement of noise from fired-process heaters (informative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, abbreviated terms and symbols

3.1 Terms and definitions
3.2 Abbreviated terms and symbols

4 General

4.1 Pressure design code
4.2 Regulations
4.3 Heater nomenclature

5 Proposals

5.1 Purchaser's responsibilities
5.2 Vendor's responsibilities
5.3 Documentation
5.4 Final reports

6 Design considerations

6.1 Process design
6.2 Combustion design
6.3 Mechanical design

7 Tubes

7.1 General
7.2 Extended surface
7.3 Materials

8 Headers

8.1 General
8.2 Plug headers
8.3 Return bends
8.4 Materials

9 Piping, terminals and manifolds

9.1 General
9.2 Allowable movement and loads
9.3 Materials

10 Tube suppports

10.1 General
10.2 Loads and allowable stress
10.3 Materials

11 Refractories and insulation

11.1 General
11.2 Brick and tile construction
11.3 Castable construction
11.4 Ceramic-fibre construction
11.5 Multi-component lining construction
11.6 Materials

12 Structures and appurtenances

12.1 General
12.2 Structures
12.3 Header boxes, doors and ports
12.4 Ladders, platforms and stairways
12.5 Materials

13 Stacks, ducts and breeching

13.1 General
13.2 Design considerations
13.3 Design methods
13.4 Static design
13.5 Wind-induced vibration design
13.6 Materials

14 Burners and auxiliary equipment

14.1 Burners
14.2 Sootblowers
14.3 Fans and drivers
14.4 Dampers and damper controls for stacks and ducts

15 Instrument and auxiliary connections

15.1 Flue gas and air
15.2 Process fluid temperature
15.3 Auxiliary connections
15.4 Tube-skin thermocouples
15.5 Access to connections

16 Shop fabrication and field erection

16.1 General
16.2 Structural-steel fabrication
16.3 Coil fabrication
16.4 Painting and galvanizing
16.5 Refractories and insulation
16.6 Preparation for shipment
16.7 Field erection

17 Inspection, examination and testing

17.1 General
17.2 Weld examination
17.3 Castings examination
17.4 Examination of other components
17.5 Testing

Annex A Equipment data sheets (informative)
Annex B Purchaser's checklist (informative)
Annex C Proposed shop-assembly conditions (informative)
Annex D Stress curves for use in the design of tube-support elements (normative)
Annex E Centrifugal fans for fired-heater systems (normative)
Annex F Air preheat systems for fired process heaters (normative)
Annex G Measurement of efficiency of fired process heaters (informative)
Annex H Stack design (informative)
Annex I Measurement of noise from fired-process heaters (informative)

Bibliography

Tuoteryhmä(t)

75.180.20 Jalostuslaitteet »

Sidokset

Velvoittavat viittaukset

ASME B17.1:1967
ASME BPVC Section 8 Division 1:2010
ASME BPVC Section 8 Division 2:2010

ASME B17.1:1967
ASME BPVC Section 8 Division 1:2010
ASME BPVC Section 8 Division 2:2010
ASME BPVC Section 8 Division 3:2010
ASTM A 105/A 105M:2012 Standard Specification for Carbon Steel Forgings for Piping Applications
ASTM A 106/A 106M:2011 Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
ASTM A 123/A 123M:2012 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
ASTM A 143/A 143M:2007 Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedure for Detecting Embrittlement
ASTM A 153/A 153M:2009 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
ASTM A 181/A 181M:2012 Standard Specification for Carbon Steel Forgings, for General-Purpose Piping
ASTM A 182/A 182M:2012 Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
ASTM A 192/A 192M:2002 Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service
ASTM A 193/A 193M:2012 Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications
ASTM A 194/A 194M:2012 Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
ASTM A 209/A 209M:2003 Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes
ASTM A 210/A 210M:2002 Standard Specification for Seamless Medium-Carbon Steel Boiler and Superheater Tubes
ASTM A 213/A 213M:2011 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
ASTM A 216/A 216M:2012 Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service
ASTM A 217/A 217M:2012 Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
ASTM A 234/A 234M:2011 Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
ASTM A 240/A 240M:2012 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ASTM A 242/A 242M:2004 Standard Specification for High-Strength Low-Alloy Structural Steel
ASTM A 283/A 283M:2012 Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
ASTM A 297/A 297M:2010 Standard Specification for Steel Castings, Iron-Chromium and Iron-Chromium-Nickel, Heat Resistant, for General Application
ASTM A 307:2010 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength
ASTM A 312/A 312Ma:2012
ASTM A 320/A 320Ma:2011
ASTM A 325:2010 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength (Withdrawn 2016)
ASTM A 335/A 335M:2011 Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
ASTM A 351/A 351Mb:2012
ASTM A 36/A 36M:2008 Standard Specification for Carbon Structural Steel
ASTM A 376/A 376M:2012 Standard Specification for Seamless Austenitic Steel Pipe for High-Temperature Service
ASTM A 384/A 384M:2007 Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies
ASTM A 385/A 385M:2011 Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip)
ASTM A 387/A 387M:2011 Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum
ASTM A 403/A 403M:2012 Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings
ASTM A 447/A 447M:2011 Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service
ASTM A 53/A 53M:2012 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
ASTM A 560/A 560M:2012 Standard Specification for Castings, Chromium-Nickel Alloy
ASTM A 572/A 572M:2012 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
ASTM A 608/A 608M:2012 Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures
ASTM B 366a:2010
ASTM B 407a:2008
ASTM B 564:2011 Standard Specification for Nickel Alloy Forgings
ASTM B 633:2011 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
ASTM C 155:1997 Standard Classification of Insulating Firebrick
ASTM C 27:1998 Standard Classification of Fireclay and High-Alumina Refractory Brick
ASTM C 332:2009 Standard Specification for Lightweight Aggregates for Insulating Concrete
ASTM C 401:2012 Standard Classification of Alumina and Alumina-Silicate Castable Refractories
ASTM C 612:2010 Standard Specification for Mineral Fiber Block and Board Thermal Insulation
AWS D 1.1-BI:2008
AWS D 1.1/D 1.1M:2010
AWS D 14.6/D 14.6M:2005
EN 10025-2:2004 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
IEC 60079-0 Corrigendum 1:2012
IEC 60079-0:2011
IEC 60079-1 Corrigendum 1:2008
IEC 60079-10-1:2008
IEC 60079-10-2:2009
IEC 60079-11 Corrigendum 1:2012
IEC 60079-11:2011
IEC 60079-13:2010
IEC 60079-14:2007
IEC 60079-15:2010
IEC 60079-17:2007
IEC 60079-18 Corrigendum 1:2009
IEC 60079-18:2009
IEC 60079-19:2010
IEC 60079-1:2007
IEC 60079-20-1 Corrigendum 1:2012
IEC 60079-20-1:2010
IEC 60079-25:2010
IEC 60079-26 Corrigendum 1:2009
IEC 60079-26:2006
IEC 60079-28 Corrigendum 1:2010
IEC 60079-28:2006
IEC 60079-29-1 Interpretation Sheet 1:2009
IEC 60079-29-1:2007
IEC 60079-29-2:2007
IEC 60079-29-4 Corrigendum 1:2010
IEC 60079-29-4:2009
IEC 60079-2:2007
IEC 60079-30-1:2007
IEC 60079-30-2:2007
IEC 60079-31 Corrigendum 1:2009
IEC 60079-31:2008
IEC 60079-33:2012
IEC 60079-35-1:2011
IEC 60079-35-2:2011
IEC 60079-5:2007
IEC 60079-6:2007
IEC 60079-7:2006
ISO 10684:2004 Fasteners -- Hot dip galvanized coatings
ISO 13704:2007 Petroleum, petrochemical and natural gas industries -- Calculation of heater-tube thickness in petroleum refineries
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles -- Specifications and test methods
ISO 15649:2001 Petroleum and natural gas industries -- Piping
ISO 1940-1:2003 Mechanical vibration -- Balance quality requirements for rotors in a constant (rigid) state -- Part 1: Specification and verification of balance tolerances
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products -- Visual assessment of surface cleanliness -- Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
NFPA 70:2011

Tekninen komitea

CEN/TC 12 Oil and gas industries including lower carbon energy »

Vahvistuspäivä

12.08.2013

Julkaisupäivä

30.08.2013

Painos

3

Sivumäärä

306

Julkaisun kieli

englanti