Geometrical product specifications (GPS). Acceptance and reverification tests for coordinate measuring systems (CMS). Part 8: CMMs with optical distance sensors (ISO 10360-8:2013)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 10360-8:2013 specifies the acceptance tests for verifying the performance of a CMM (coordinate measuring machine) when measuring lengths as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the CMM. The acceptance and reverification tests are applicable only to Cartesian CMMs with optical distance sensors. While it does not explicitly apply to non-Cartesian CMMs, the parties may apply ISO 10360-8:2013 to non-Cartesian CMMs by mutual agreement. It is not intended to be applicable to CMMs whose measuring volume is significantly smaller than the size of the test sphere. However, the principle, artefacts and procedure of the test described are useful for the acceptance and reverification tests of those CMMs ? either as it is or with modifying the parameters such as the size of the test artefacts and the number of measurements. ISO 10360-8:2013 specifies performance requirements that can be assigned by the manufacturer or the user of the CMM, the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements, rules for verifying conformance, and applications for which the acceptance and reverification tests can be used.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Requirements for metrological characteristics
5.1 Environmental conditions
5.2 Operating conditions
5.3 Probing form error
5.4 Probing dispersion value
5.5 Probing size error
5.6 Probing size error All
5.7 Length measurement error
5.8 Flat form measurement error
5.9 Workpiece loading effects
6 Acceptance tests and reverification tests
6.1 General
6.2 Probing characteristics
6.3 Length measurement error
6.4 Flat form measurement error
7 Compliance with specifications
7.1 Acceptance test
7.2 Reverification test
8 Applications
8.1 Acceptance test
8.2 Reverification test
8.3 Interim check
9 Indication in product documentation and data sheets
Annex A Structural resolution test (informative)
Annex B Artefacts that represent a calibrated test length (normative)
Annex C Alignment of artefacts (informative)
Annex D Articulated location value of CMMs with articulating probing system for optical distance sensors (normative)
Annex E Relation to the GPS matrix model (informative)
ISO 10360-1:2000 Geometrical Product Specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 1: Vocabulary
ISO 10360-2:2009 Geometrical product specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 2: CMMs used for measuring linear dimensions
ISO 10360-5:2010 Geometrical product specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 5: CMMs using single and multiple stylus contacting probing systems
ISO 10360-1:2000 Geometrical Product Specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 1: Vocabulary
ISO 10360-2:2009 Geometrical product specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 2: CMMs used for measuring linear dimensions
ISO 10360-5:2010 Geometrical product specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 5: CMMs using single and multiple stylus contacting probing systems
ISO 14253-1:2013 Geometrical product specifications (GPS) -- Inspection by measurement of workpieces and measuring equipment -- Part 1: Decision rules for proving conformity or nonconformity with specifications
ISO/IEC Guide 99:2007 International vocabulary of metrology -- Basic and general concepts and associated terms (VIM)
ISO/TS 23165:2006 Geometrical product specifications (GPS) -- Guidelines for the evaluation of coordinate measuring machine (CMM) test uncertainty