ISO 13274:2013 specifies the requirements and test methods for compatibility testing of plastics packagings/Intermediate Bulk Containers (IBCs) and composite packagings/IBCs with plastics inners containing liquids. The testing involves storage with the liquid to be transported. For polyethylene-based packaging, testing with a standard liquid as defined in The European Agreement concerning the International Carriage of Dangerous Goods by Road may be undertaken. Annex B describes small-scale laboratory tests that may be used to determine the assimilation of those products to be carried with the standard liquids. Where there is any contradiction between ISO 13274:2013 and any applicable regulation, the regulation always takes precendence.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test requirements
4.1 General
4.2 Conditioning
4.3 Post-conditioning inspection
4.4 Drop test
4.5 Stacking test
4.6 Hydraulic pressure test
4.7 Leakproofness test
4.8 Bottom lift test
4.9 Top lift test
4.10 Vibration test
4.11 Permeability testing
4.12 Equivalent testing
5 Selection and preparation of packagings/IBCs
6 Additional information to be provided for assimilation
7 Facilities for testing
8 Conditioning procedures
8.1 General
8.2 Ambient conditioning
8.3 Accelerated conditioning
8.4 Procedure following the conditioning period
8.5 Reuse of standard liquids
9 Test report
Annex A Applicability of standard liquids to polyethylene types (informative)
Annex B Small-scale laboratory tests to assess packaged substances against standard liquids (normative)
ISO 1133-1:2011 Plastics -- Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics -- Part 1: Standard method
ISO 11403-3:1999 Plastics -- Acquisition and presentation of comparable multipoint data -- Part 3: Environmental influences on properties
ISO 11542-2:1998 Plastics -- Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
ISO 1133-1:2011 Plastics -- Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics -- Part 1: Standard method
ISO 11403-3:1999 Plastics -- Acquisition and presentation of comparable multipoint data -- Part 3: Environmental influences on properties
ISO 11542-2:1998 Plastics -- Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
ISO 1183-1:2012 Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1628-3:2010 Plastics -- Determination of the viscosity of polymers in dilute solution using capillary viscometers -- Part 3: Polyethylenes and polypropylenes
ISO 16495:2013 Packaging -- Transport packaging for dangerous goods -- Test methods
ISO 16770:2004 Plastics -- Determination of environmental stress cracking (ESC) of polyethylene -- Full-notch creep test (FNCT)
ISO 1872-2:2007 Plastics -- Polyethylene (PE) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties
ISO 2818:1994 Plastics -- Preparation of test specimens by machining
ISO 291:2008 Plastics -- Standard atmospheres for conditioning and testing
ISO 527-2:2012 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics