Petroleum, petrochemical and natural gas industries. Axial and centrifugal compressors and expander-compressors. Part 1: General requirements (ISO 10439-1:2015)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 10439 specifies minimum requirements and gives recommendations for axial compressors, single-shaft, and integrally geared process centrifugal compressors, and expander-compressors for special purpose applications that handle gas or process air in the petroleum, petrochemical, and natural gas industries. ISO 10439-1:2015 specifies general requirements applicable to all such machines. ISO 10439-1:2015 does not apply to fans (these are covered by API 673) or blowers that develop less than 34 kPa (5 psi) pressure rise above atmospheric pressure. It also does not apply to packaged, integrally geared centrifugal plant, and instrument air compressors, which are covered by API 672. Hot gas expanders over 300 °C (570 °F) are not covered by ISO 10439-1:2015. ISO 10439-1:2015 contains information pertinent to all equipment covered by the other parts of ISO 10439. It shall be used in conjunction with the following parts of ISO 10439, as applicable to the specific equipment covered:
ISO 10439-2; ISO 10439-3 ISO 10439-4
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, abbreviated terms and definitions
3.1 Terms and definitions
3.2 Abbreviated terms
4 General
4.1 Dimensions and units
4.2 Statutory requirements
4.3 Unit responsibility
4.4 Basic design
4.5 Materials
4.6 Casings
4.7 Rotating elements
4.8 Dynamics
4.9 Bearings and bearing housings
4.10 Shaft and seals
4.11 Integral gearing
4.12 Nameplates and rotation arrows
5 Accessories
5.1 Drivers and gearing
5.2 Couplings and guards
5.3 Lubrication and sealing systems
5.4 Mounting plates
5.5 Controls and instrumentation
5.6 Piping and appurtenances
5.7 Special tools
6 Inspection, testing, and preparation for shipment
6.1 General
6.2 Inspection
6.3 Testing
6.4 Preparation for shipment
7 Supplier’s data
7.1 General
7.2 Proposals
7.3 Contract data
Annex A Procedure for the determination of residual unbalance (normative)
Annex B Typical shaft end seals (informative)
Annex C Requirements for lateral analysis reports (normative)
Annex D Requirements for torsional analysis reports (normative)
Annex E Magnetic bearings (normative)
Annex F Dry gas seal testing at manufacturer's shop (normative)
Annex G Guidelines for anti-surge systems (informative)
API STD 613:2003
ASME B1.1:2003
ASME B1.20.1:2013
ASME B16.11:2011
ASME B16.1:2010
ASME B16.42:2011
ASME B16.47:2011
ASME B16.5:2013
ASTM A 247:2010 Standard Test Method for Evaluating the Microstructure of Graphite in Iron Castings
ASTM A 395:1988
ASTM E 125:1963 Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings
ASTM E 165:2009
ASTM E 709:2014 Standard Guide for Magnetic Particle Testing
AWS D 1.1:2000
EN 55011:2016 Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement
EN IEC 61000-6-2:2019 Sähkömagneettinen yhteensopivuus (EMC). Osa 6-2: Yleiset standardit. Häiriönsieto teollisuusympäristöissä
IEC 60079-10-1:2008
ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements
ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems
ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems
ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 4: Self-acting gas seal support systems
ISO 10441:2007 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- Special-purpose applications
ISO 14839-3:2006 Mechanical vibration -- Vibration of rotating machinery equipped with active magnetic bearings -- Part 3: Evaluation of stability margin
ISO 15156-3:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO 21940-32:2012 Mechanical vibration -- Rotor balancing -- Part 32: Shaft and fitment key convention
ISO 261:1998 ISO general purpose metric screw threads -- General plan
ISO 6708:1995 Pipework components -- Definition and selection of DN (nominal size)
ISO 7005-1:2011 Pipe flanges -- Part 1: Steel flanges for industrial and general service piping systems
ISO 7005-2:1988 Metallic flanges -- Part 2: Cast iron flanges
ISO 8068:2006 Lubricants, industrial oils and related products (class L) -- Family T (Turbines) -- Specification for lubricating oils for turbines
NACE MR 0103:2012
NACE SP 0472:2010
NFPA 70:2014
SAE J 518:2013