CEN/TR 13445-101:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

This Technical Report presents an application of EN 13445 through an example of design and fabrication of an unfired pressure vessel. Every step is described as far as possible:
- Material choice;
- Design and calculation;
- Fabrication;
- Inspection and testing;
using the following part of EN 13445:
- EN 13445-1:2009;
- EN 13445-2:2009;
- EN 13445-3:2009;
- EN 13445-4:2009;
- EN 13445-5:2009 .
As applicable, some choices for design or fabrication are made according to “the state of art” practice.
Some parts of EN 13445 are reproduced in order to show which requirements are relevant to the design and fabrication of the target vessel.

Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).

Tuoteryhmä(t)

23.020.30 Painelaitteet »

Sidokset

Velvoittavat viittaukset

CR ISO 15608:2000 Welding - Guidelines for a metallic material grouping system (ISO/TR 15608:2000)
EN 10025-2:2004 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10028-1:2007 Flat products made of steels for pressure purposes - Part 1: General requirements

CR ISO 15608:2000 Welding - Guidelines for a metallic material grouping system (ISO/TR 15608:2000)
EN 10025-2:2004 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
EN 10028-1:2007 Flat products made of steels for pressure purposes - Part 1: General requirements
EN 10028-2:2003 Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
EN 10029:2010 Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape
EN 10204:2004 Metallic products - Types of inspection documents
EN 10216-3:2002 Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes
EN 10222-4:1998 Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength
EN 10269:1999 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 10269:1999/A1:2006 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 1092-1:2007 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges
EN 12560-4:2001 Flanges and their joints - Gaskets for Class-designated flantes - Part 4: Corrugated, flat or grooved metallic and filled metallic gaskets for use with steel flanges
EN 1418:1997 Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN 1515-3:2005 Flanges and their joints - Bolting - Part 3: Classification of bolt materials for steel flanges, class designated
EN 1515-4:2009 Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC
EN 1759-1:2004 Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24
EN 287-1:2004 Qualification test of welders - Fusion welding - Part 1: Steels
EN 287-1:2004/A2:2006 Qualification test of welders - Fusion welding - Part 1: Steels
EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
EN 764-5:2002 Pressure Equipment - Part 5: Compliance and Inspection Documentation of Materials
EN ISO 15614-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys (ISO 15614-1:2004)

Tekninen komitea

CEN/TC 54 Unfired pressure vessels »

Vahvistuspäivä

18.05.2015

Julkaisupäivä

05.06.2015

Painos

1

Sivumäärä

95

Julkaisun kieli

englanti