SFS-EN 61076-3-118:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

IEC 61076-3-118:2010 establishes specifications and test requirements for a connector with four contacts plus PE contact, for use in industrial environments. This standard also specifies free and fixed connectors, with round contacts, suitable for screw or crimp terminations. Other terminations techniques, as solder or printed board connections are upon agreement between manufacturer and user. The free and fixed connectors have a push-pull locking mechanism for IP65 and IP67 protection according to IEC 60529. The PE contact is first-make last-break. Connectors according this International Standard are without breaking capacity COC according to IEC 61984, therefore they are not intended to be engaged or disengaged in normal use when live or under load, if not otherwise specified by the manufacturer.

Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.

Tuoteryhmä(t)

31.220.10 Pistokytkimet. Koskettimet »

Sidokset

Velvoittavat viittaukset

EN 60068-1:1994 Environmental testing - Part 1: General and guidance
EN 60352-1:1997 Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance
EN 60352-2:1994 Solderless connections - Part 2: Solderless crimped connections - General requirements, test methods and practical guidance

EN 60068-1:1994 Environmental testing - Part 1: General and guidance
EN 60352-1:1997 Solderless connections - Part 1: Wrapped connections - General requirements, test methods and practical guidance
EN 60352-2:1994 Solderless connections - Part 2: Solderless crimped connections - General requirements, test methods and practical guidance
EN 60352-2:1994/A1:1997 Solderless connections - Part 2: Solderless crimped connections - General requirements, test methods and practical guidance
EN 60352-2:1994/A2:2002 Solderless connections - Part 2: Solderless crimped connections - General requirements, test methods and practical guidance
EN 60352-2:2006 Solderless connections - Part 2: Crimped connections - General requirements, test methods and practical guidance
EN 60352-2:2006/A1:2013 Solderless connections - Part 2: Crimped connections - General requirements, test methods and practical guidance
EN 60352-3:1994 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
EN 60352-4:1994 Solderless connections - Part 4: Solderless non-accessible insulation displacement connections - General requirements, test methods and practical guidance
EN 60352-4:1994/A1:2000 Solderless connections - Part 4: Solderless non-accessible insulation displacement connections - General requirements, test methods and practical guidance
EN 60352-5:1995 Solderless connections - Part 5: Solderless press-in connections - General requirements, test methods and practical guidance
EN 60352-5:2001 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
EN 60352-5:2001/A1:2003 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
EN 60352-5:2008 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
EN 60352-5:2012 Solderless connections - Part 5: Press-in connections - General requirements, test methods and practical guidance
EN 60352-6:1997 Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance
EN 60352-7:2002 Solderless connections - Part 7: Spring clamp connections - General requirements, test methods and practical guidance
EN 60352-8:2011 Solderless connections - Part 8: Compression mount connections - General requirements, test methods and practical guidance
EN 60512-1-100:2006 Connectors for electronic equipment - Tests and measurements - Part 1-100: General - Applicable publications
EN 60512-1-2:2002 Connectors for electronic equipment - Tests and measurements - Part 1-2: General examination - Test 1b: Examination of dimension and mass
EN 60529:1991 Sähkölaitteiden kotelointiluokat (IP-koodi)
EN 60999-1:2000 Kytkentätarvikkeet. Kuparijohtimien liittämiseen tarkoitettujen ruuvityyppisten ja ruuvittomien puristusosien turvallisuusvaatimukset. Osa 1: Yleiset vaatimukset ja erityisvaatimukset 0,2 mm2 ... 35 mm2 johtimien liittämiseen tarkoitetuille puristusosille
EN 60999-2:2003 Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included)
EN 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
EN 61984:2009 Connectors - Safety requirements and tests
EN 62197-1:2006 Connectors for electronic equipment - Quality assessment requirements - Part 1: Generic specification
EN ISO 11469:2000 Plastics - Generic identification and marking of plastics products (ISO 11469:2000)
EN ISO 1302:2002 Geometrical Product Specifications (GPS) - Indication of surface texture in technical product documentation (ISO 1302:2002)
EN ISO 21920-1:2022 Geometrical product specifications (GPS) - Surface texture: Profile - Part 1: Indication of surface texture (ISO 21920-1:2021)
IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
IEC Guide 109:2003
IEC Guide 114:2005

Tekninen komitea

CLC/SR 48B Electrical connectors »

Vahvistuspäivä

05.10.2015

Julkaisupäivä

01.03.2016

Painos

1

Sivumäärä

36

Julkaisun kieli

englanti