Verkkokauppa
SFS-EN ISO 20844:en
Petroleum and related products. Determination of the shear stability of polymer-containing oils using a diesel injector nozzle (ISO 20844:2015)
Soveltamisala
Suomenkielistä soveltamisalaa ei ole saatavissa.
ISO 20844:2015 specifies a method to assess the resistance to shear stresses applied to mineral oils, synthetic oils, and other fluids containing polymers, when passed through a specified diesel injector nozzle. The shear stability is measured by the change in viscosity of the fluid under test, brought about by the polymer degradation during stress. Under normal circumstances, this International Standard is applied to hydraulic fluids of categories HR and HV as defined in ISO 6743-4[1] and specified in ISO 11158 [2], but it may also be applied to fire-resistant hydraulic fluids within categories HFA, HFB, HFC, and HFD, with modified conditions as specified in ISO 12922[3].
No formal correlation has been established between the viscosity loss, or the absence of viscosity loss, obtained using the procedures described in this International Standard and that of oils and fluids in actual service. However, it provides standardized conditions for the evaluation of polymer stability under minimized thermal and oxidative stresses. It is normally used by manufacturers of fluids and additives, and users, as a means of ranking existing and potential formulations.
NOTE Changes to properties other than viscosity are specified in some specifications, but these are not covered by the procedures specified in this International Standard.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
ISO 20844:2015 specifies a method to assess the resistance to shear stresses applied to mineral oils, synthetic oils, and other fluids containing polymers, when passed through a specified diesel injector nozzle. The shear stability is measured by the change in viscosity of the fluid under test, brought about by the polymer degradation during stress. Under normal circumstances, this International Standard is applied to hydraulic fluids of categories HR and HV as defined in ISO 6743-4[1] and specified in ISO 11158 [2], but it may also be applied to fire-resistant hydraulic fluids within categories HFA, HFB, HFC, and HFD, with modified conditions as specified in ISO 12922[3].
No formal correlation has been established between the viscosity loss, or the absence of viscosity loss, obtained using the procedures described in this International Standard and that of oils and fluids in actual service. However, it provides standardized conditions for the evaluation of polymer stability under minimized thermal and oxidative stresses. It is normally used by manufacturers of fluids and additives, and users, as a means of ranking existing and potential formulations.
NOTE Changes to properties other than viscosity are specified in some specifications, but these are not covered by the procedures specified in this International Standard.
Tämän julkaisun valmistelusta Suomessa vastaa SFS Suomen Standardit, puh. 09 149 9331.
Sisällysluettelo
Tuoteryhmä(t)
Sidokset
Velvoittavat viittaukset
ISO 3104:1994 Petroleum products -- Transparent and opaque liquids -- Determination of kinematic viscosity and calculation of dynamic viscosity
ISO 3170:2004 Petroleum liquids -- Manual sampling
ISO 4113:2010 Road vehicles -- Calibration fluids for diesel injection equipment
ISO 3170:2004 Petroleum liquids -- Manual sampling
ISO 4113:2010 Road vehicles -- Calibration fluids for diesel injection equipment
Tekninen komitea
Direktiivi
92/104/EC Vähimmäisvaatimuksista avo- ja kaivoslouhintateollisuuden työntekijöiden turvallisuuden ja terveyden suojelun parantamiseksi
http://ec.europa.eu »
http://ec.europa.eu »
Vahvistuspäivä
09.11.2015
Julkaisupäivä
27.11.2015
Painos
2
Sivumäärä
15
Julkaisun kieli
englanti