Mechanical vibration. Laboratory method for evaluating vehicle seat vibration. Part 1: Basic requirements (ISO 10326-1:2016, Corrected version 2017-02)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 10326-1:2016 specifies basic requirements for the laboratory testing of vibration transmission through a vehicle seat to the occupant. These methods for measurement and analysis make it possible to compare test results from different laboratories for equivalent seats. It specifies the test method, the instrumentation requirements, the measuring assessment method and the way to report the test result. ISO 10326-1:2016 applies to specific laboratory seat tests which evaluate vibration transmission to the occupants of any type of seat used in vehicles and mobile off-road machinery. Application standards for specific vehicles refer to this document when defining the test input vibration that is typical for the vibration characteristics of the type or class of vehicle or machinery in which the seat is to be fitted. NOTE Examples of application standards are given in the bibliography.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Instrumentation
5.1 Acceleration transducers
5.2 Transducer mounting
5.3 Frequency weighting
5.4 Calibration
6 Vibration equipment
6.1 Physical characteristics
6.2 Control system
7 Safety requirements
8 Test conditions
8.1 Test seat
8.2 Test persons and posture
8.3 Other possibilities
9 Test input vibration
9.1 General
9.2 Simulated input vibration test
9.3 Tolerances on input vibration
9.4 Transfer function with sinusoidal vibration input
9.5 Damping test
10 Test procedure
10.1 General
10.2 Simulated input vibration test
10.3 Damping test
11 Acceptance
12 Test report
Annex A Test method for assessing the ability of a seat suspension to control the effects of impacts caused by over-travel (informative)
Annex B Example of a simulated input test signal specified by the PSD (informative)
ISO 13090-1:1998 Mechanical vibration and shock -- Guidance on safety aspects of tests and experiments with people -- Part 1: Exposure to whole-body mechanical vibration and repeated shock
ISO 16063-1 AMD 1:2016
ISO 16063-11:1999 Methods for the calibration of vibration and shock transducers -- Part 11: Primary vibration calibration by laser interferometry
ISO 13090-1:1998 Mechanical vibration and shock -- Guidance on safety aspects of tests and experiments with people -- Part 1: Exposure to whole-body mechanical vibration and repeated shock
ISO 16063-1 AMD 1:2016
ISO 16063-11:1999 Methods for the calibration of vibration and shock transducers -- Part 11: Primary vibration calibration by laser interferometry
ISO 16063-12:2002 Methods for the calibration of vibration and shock transducers -- Part 12: Primary vibration calibration by the reciprocity method
ISO 16063-12:2002/Cor 1:2008
ISO 16063-13:2001 Methods for the calibration of vibration and shock transducers -- Part 13: Primary shock calibration using laser interferometry
ISO 16063-15:2006 Methods for the calibration of vibration and shock transducers -- Part 15: Primary angular vibration calibration by laser interferometry
ISO 16063-16:2014 Methods for the calibration of vibration and shock transducers -- Part 16: Calibration by Earth's gravitation
ISO 16063-17:2016 Methods for the calibration of vibration and shock transducers -- Part 17: Primary calibration by centrifuge
ISO 16063-1:1998 Methods for the calibration of vibration and shock transducers -- Part 1: Basic concepts
ISO 16063-21 AMD 1:2016
ISO 16063-21:2003 Methods for the calibration of vibration and shock transducers -- Part 21: Vibration calibration by comparison to a reference transducer
ISO 16063-21:2003/Cor 1:2009
ISO 16063-22 AMD 1:2014
ISO 16063-22:2005 Methods for the calibration of vibration and shock transducers -- Part 22: Shock calibration by comparison to a reference transducer
ISO 16063-31:2009 Methods for the calibration of vibration and shock transducers -- Part 31: Testing of transverse vibration sensitivity
ISO 16063-32:2016 Methods for the calibration of vibration and shock transducers -- Part 32: Resonance testing -- Testing the frequency and the phase response of accelerometers by means of shock excitation
ISO 16063-41:2011 Methods for the calibration of vibration and shock transducers -- Part 41: Calibration of laser vibrometers
ISO 16063-42:2014 Methods for the calibration of vibration and shock transducers -- Part 42: Calibration of seismometers with high accuracy using acceleration of gravity
ISO 16063-43:2015 Methods for the calibration of vibration and shock transducers -- Part 43: Calibration of accelerometers by model-based parameter identification
ISO 2631-1:1997 Mechanical vibration and shock -- Evaluation of human exposure to whole-body vibration -- Part 1: General requirements
ISO 5347-12:1993 Methods for the calibration of vibration and shock pick-ups -- Part 12: Testing of transverse shock sensitivity
ISO 5347-13:1993 Methods for the calibration of vibration and shock pick-ups -- Part 13: Testing of base strain sensitivity
ISO 5347-15:1993 Methods for the calibration of vibration and shock pick-ups -- Part 15: Testing of acoustic sensitivity
ISO 5347-16:1993 Methods for the calibration of vibration and shock pick-ups -- Part 16: Testing of mounting torque sensitivity
ISO 5347-17:1993 Methods for the calibration of vibration and shock pick-ups -- Part 17: Testing of fixed temperature sensitivity
ISO 5347-18:1993 Methods for the calibration of vibration and shock pick-ups -- Part 18: Testing of transient temperature sensitivity
ISO 5347-19:1993 Methods for the calibration of vibration and shock pick-ups -- Part 19: Testing of magnetic field sensitivity
ISO 5347-22:1997 Methods for the calibration of vibration and shock pick-ups -- Part 22: Accelerometer resonance testing -- General methods
ISO 5347-8:1993 Methods for the calibration of vibration and shock pick-ups -- Part 8: Primary calibration by dual centrifuge
ISO 8041:2005 Human response to vibration -- Measuring instrumentation