The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-1 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. For the purposes of ISO 10350-1, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding. NOTE ISO 10350-2 deals specifically with long- or continuous-fibre-reinforced plastics.
Tämän julkaisun valmistelusta Suomessa vastaa Kemesta ry, puh. 040 820 4888.
IEC 60112:2003
IEC 60243-1:2013
IEC 60250:1969
IEC 60296:2012
IEC 60695-11-10:2013
IEC 60695-11-20:2015
IEC 62631-3-1:2016
IEC 62631-3-2:2015
ISO 10724-1:1998 Plastics -- Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) -- Part 1: General principles and moulding of multipurpose test specimens
ISO 10724-2:1998 Plastics -- Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) -- Part 2: Small plates
ISO 1133-1:2011 Plastics -- Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics -- Part 1: Standard method
ISO 1133-2:2011 Plastics -- Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics -- Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 11357-2:2013 Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of glass transition temperature and glass transition step height
ISO 11357-3:2011 Plastics -- Differential scanning calorimetry (DSC) -- Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11359-2:1999 Plastics -- Thermomechanical analysis (TMA) -- Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 1183-1:2012 Plastics -- Methods for determining the density of non-cellular plastics -- Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics -- Methods for determining the density of non-cellular plastics -- Part 2: Density gradient column method
ISO 1183-3:1999 Plastics -- Methods for determining the density of non-cellular plastics -- Part 3: Gas pyknometer method
ISO 178:2010 Plastics -- Determination of flexural properties
ISO 179-1:2010 Plastics -- Determination of Charpy impact properties -- Part 1: Non-instrumented impact test
ISO 179-2:1997 Plastics -- Determination of Charpy impact properties -- Part 2: Instrumented impact test
ISO 20753:2008 Plastics -- Test specimens
ISO 2577:2007 Plastics -- Thermosetting moulding materials -- Determination of shrinkage
ISO 2818:1994 Plastics -- Preparation of test specimens by machining
ISO 293:2004 Plastics -- Compression moulding of test specimens of thermoplastic materials
ISO 294-1:2017 Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 294-3:2002 Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 3: Small plates
ISO 294-4:2001 Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 4: Determination of moulding shrinkage
ISO 295:2004 Plastics -- Compression moulding of test specimens of thermosetting materials
ISO 306:2013 Plastics -- Thermoplastic materials -- Determination of Vicat softening temperature (VST)
ISO 3915:1981 Plastics -- Measurement of resistivity of conductive plastics
ISO 4589-2:2017 Plastics -- Determination of burning behaviour by oxygen index -- Part 2: Ambient-temperature test
ISO 527-1:2012 Plastics -- Determination of tensile properties -- Part 1: General principles
ISO 527-2:2012 Plastics -- Determination of tensile properties -- Part 2: Test conditions for moulding and extrusion plastics
ISO 62:2008 Plastics -- Determination of water absorption
ISO 6603-2:2000 Plastics -- Determination of puncture impact behaviour of rigid plastics -- Part 2: Instrumented impact testing
ISO 75-1:2013 Plastics -- Determination of temperature of deflection under load -- Part 1: General test method
ISO 75-2:2013 Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite
ISO 8256:2004 Plastics -- Determination of tensile-impact strength
ISO 899-1:2003 Plastics -- Determination of creep behaviour -- Part 1: Tensile creep