ISO 19085-3:2017 gives the safety requirements and measures for numerically controlled (NC) boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.1), hereinafter referred to as "machines". ISO 19085-3:2017 deals with all significant hazards, hazardous situations and events, listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and measures for controls
5.1 Safety and reliability of control systems
5.2 Control devices
5.3 Start
5.4 Safe stops
5.5 Braking function of tool spindles
5.6 Mode selection
5.7 Spindle speed changing
5.8 Failure of any power supply
5.9 Manual reset control
5.10 Enabling control
5.11 Machine moving parts speed monitoring
5.12 Time delay
5.13 Teleservice
6 Safety requirements and measures for protection against mechanical hazards
6.1 Stability
6.2 Risk of break-up during operation
6.3 Tool holder and tool design
6.4 Braking
6.5 Safeguards
6.6 Prevention of access to moving parts
6.7 Impact hazard
6.8 Clamping device
6.9 Measures against ejection
6.10 Workpiece support and guides
7 Safety requirements and measures for protection against other hazards
7.1 Fire
7.2 Noise
7.3 Emission of chips and dust
7.4 Electricity
7.5 Ergonomics and handling
7.6 Lighting
7.7 Pneumatics
7.8 Hydraulics
7.9 Electromagnetic compatibility
7.10 Laser
7.11 Static electricity
7.12 Errors of fitting
7.13 Isolation
7.14 Maintenance
8 Information for use
8.1 Warning devices
8.2 Marking
8.3 Instruction handbook
Annex A Performance levels required (informative)
Annex B Test for braking function (normative)
Annex C Stability test for displaceable machines (normative)
Annex D Impact test for guards (normative)
Annex E Noise emission measurement for machines not in ISO 7960 (normative)
Annex F Impact test for curtains (normative)
Annex G Wear test for curtains (normative)
Annex H Dynamic test for pressure-sensitive bumpers, edges, trip bars, trip plates (normative)
Annex ZA Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC (informative)
EN 847-1:2013 Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN 847-2:2013 Tools for woodworking - Safety requirements - Part 2: Requirements for the shank of shank mounted milling
ISO 12100:2010 Safety of machinery -- General principles for design -- Risk assessment and risk reduction
EN 847-1:2013 Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN 847-2:2013 Tools for woodworking - Safety requirements - Part 2: Requirements for the shank of shank mounted milling
ISO 12100:2010 Safety of machinery -- General principles for design -- Risk assessment and risk reduction
ISO 13849-1:2015 Safety of machinery -- Safety-related parts of control systems -- Part 1: General principles for design
ISO 13856-3:2013 Safety of machinery -- Pressure-sensitive protective devices -- Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices
ISO 13857:2008 Safety of machinery -- Safety distances to prevent hazard zones being reached by upper and lower limbs
ISO 19085-1:2017 Woodworking machines -- Safety -- Part 1: Common requirements
ISO 2602:1980 Statistical interpretation of test results -- Estimation of the mean -- Confidence interval
ISO 4413:2010 Hydraulic fluid power -- General rules and safety requirements for systems and their components
ISO 4414:2010 Pneumatic fluid power -- General rules and safety requirements for systems and their components