SFS-EN IEC 62688:2018:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

IEC 62688:2017(E) describes the fundamental construction and testing requirements for Concentrator Photovoltaic (CPV) modules and assemblies in order to provide safe electrical and mechanical operation during their expected lifetime. Specific topics are provided to assess the prevention of electrical shock, fire hazards, and personal injury due to mechanical and environmental stresses. This document attempts to define the basic requirements for various application classes of concentrator photovoltaic modules and assemblies, but does not encompass all national and regional codes. This document is designed so that its test sequence can coordinate with those of IEC 62108, so that a single set of samples may be used to perform both the safety and performance evaluation of a CPV module and assembly.

Tämän julkaisun valmistelusta Suomessa vastaa SESKO ry, puh. 050 571 6048.

Tuoteryhmä(t)

27.160 Aurinkoenergiatekniikka »

Sidokset

Velvoittavat viittaukset

ANSI/UL 1703:2015
ANSI/UL 746B:2014
ANSI/UL 746C:2004

ANSI/UL 1703:2015
ANSI/UL 746B:2014
ANSI/UL 746C:2004
ANSI/UL 790:2004
ASTM D1002-10 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D257-14 Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D3755-14 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Under Direct-Voltage Stress
ASTM E162-13 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
EN 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
EN 60216-5:2008 Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
EN 60243-2:2014 Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage
EN 60529:1991 Sähkölaitteiden kotelointiluokat (IP-koodi)
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
EN 60664-3:2017 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
EN 60695-1-10:2017 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
EN 60695-1-11:2015 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
EN 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
EN 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
EN 60947-1:2007 Pienjännitekytkinlaitteet. Osa 1: Pienjännitekytkinlaitteet. Yleiset vaatimukset
EN 60950-1:2006 Information technology equipment - Safety - Part 1: General requirements
EN 61032:1998 Koteloinnilla aikaansaatu henkilö- ja esinesuojaus. Todentamisessa käytettävät koettimet
EN 61140:2016 Suojaus sähköiskulta. Asennusten ja laitteiden yhteiset ominaisuudet
EN 61215-2:2017 Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
EN 61508-1:2010 Sähköisten/elektronisten/ohjelmoitavien elektronisten turvallisuuteen liittyvien järjestelmien toiminnallinen turvallisuus. Osa 1: Yleiset vaatimukset
EN 61508-2:2001 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems
EN 61508-2:2010 Sähköisten/elektronisten/ohjelmoitavien elektronisten turvallisuuteen liittyvien järjestelmien toiminnallinen turvallisuus. Osa 2: Vaatimukset sähköisille/elektronisille/ohjelmoitaville elektronisille turvallisuuteen liittyville järjestelmille
EN 61508-3:2001 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 3: Software requirements
EN 61508-3:2010 Sähköisten/elektronisten/ohjelmoitavien elektronisten turvallisuuteen liittyvien järjestelmien toiminnallinen turvallisuus. Osa 3: Ohjelmistovaatimukset
EN 61508-4:2001 Sähköisten/elektronisten/ohjelmoitavien elektronisten turvallisuuteen liittyvien järjestelmien toiminnallinen turvallisuus. Osa 4: Määritelmät ja lyhenteet
EN 61508-4:2010 Sähköisten/elektronisten/ohjelmoitavien elektronisten turvallisuuteen liittyvien järjestelmien toiminnallinen turvallisuus. Osa 4: Määritelmät ja lyhenteet
EN 61508-5:2001 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 5: Examples of methods for the determination of safety integrity levels
EN 61508-5:2010 Sähköisten/elektronisten/ohjelmoitavien elektronisten turvallisuuteen liittyvien järjestelmien toiminnallinen turvallisuus. Osa 5: Esimerkkejä menetelmistä turvallisuuden eheyden tasojen määrittämiseksi
EN 61508-6:2001 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3
EN 61508-6:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 6: Guidelines on the application of IEC 61508-2 and IEC 61508-3
EN 61508-7:2001 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures
EN 61508-7:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures
EN 62108:2016 Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval
EN 62305-2:2012 Protection against lightning - Part 2: Risk management
EN 62305-3:2011 Protection against lightning - Part 3: Physical damage to structures and life hazard
EN 62670-1:2014 Photovoltaic concentrators (CPV) - Performance testing - Part 1: Standard conditions
EN 62852:2015 Connectors for DC-application in photovoltaic systems - Safety requirements and tests
EN IEC 60112:2020 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
EN IEC 60216-5:2022 Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative temperature index (RTI) of an insulating material
EN IEC 60695-2-10:2021 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
EN IEC 60904-3:2019 Photovoltaic devices - Part 3: Measurement principles for terrestrial photovoltaic (PV) solar devices with reference spectral irradiance data
EN IEC 60947-1:2021 Low-voltage switchgear and controlgear - Part 1: General rules
EN IEC 61215-2:2021 Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures
EN IEC 61730-1:2018 Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction
EN IEC 61730-2:2018 Photovoltaic (PV) module safety qualification - Part 2: Requirements for testing
EN IEC 62368-1:2020 Audio/video, information and communication technology equipment - Part 1: Safety requirements
EN IEC 62368-1:2024 Audio/video, information and communication technology equipment - Part 1: Safety requirements
EN IEC 62790:2020 Junction boxes for photovoltaic modules - Safety requirements and tests
EN ISO 1456:2009 Metallic and other inorganic coatings - Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium (ISO 1456:2009)
EN ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009)
EN ISO 1461:2022 Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2022)
EN ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010)
EN ISO 179-1:2023 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2023)
EN ISO 2081:2018 Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2018)
EN ISO 4892-2:2013 Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013)
EN ISO 527-1:2019 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2019)
EN ISO 527-2:1996 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:1993 including Corr 1:1994)
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN ISO 527-3:1995 Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO 527-3:1995)
EN ISO 527-3:2018 Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO 527-3:2018)
EN ISO 527-4:1997 Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997)
EN ISO 527-4:2021 Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:2021)
EN ISO 527-4:2023 Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:2023)
EN ISO 527-5:1997 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:1997)
EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
EN ISO 527-5:2021 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2021)
IEC 62548:2016 Photovoltaic (PV) arrays - Design requirements
IEC/TR 60664-2-1:2011 Insulation coordination for equipment within low-voltage systems - Part 2-1: Application guide - Explanation of the application of the IEC 60664 series, dimensioning examples and dielectric testing
IEC/TS 61836:2016 Solar photovoltaic energy systems - Terms, definitions and symbols
ISO 261:1998 ISO general purpose metric screw threads -- General plan
ISO 262:1998 ISO general purpose metric screw threads -- Selected sizes for screws, bolts and nuts
ISO 5657:1997 Reaction to fire tests -- Ignitability of building products using a radiant heat source
ISO 8124-1:2009 Safety of toys -- Part 1: Safety aspects related to mechanical and physical properties
ISO 834-1:1999 Fire-resistance tests -- Elements of building construction -- Part 1: General requirements
ISO/TR 834-3:2012 Fire-resistance tests -- Elements of building construction -- Part 3: Commentary on test method and guide to the application of the outputs from the fire-resistance test

Tekninen komitea

CLC/TC 82 Solar photovoltaic energy systems »

Vahvistuspäivä

16.02.2018

Julkaisupäivä

20.02.2018

Painos

1

Sivumäärä

84

Julkaisun kieli

englanti