ISO 16228:2017 specifies the different types of fastener inspection documents issued by the fastener manufacturer or distributor and/or by the external authorized representative on specific request of the purchaser at the time of the order. - declaration of compliance (F2.1); - test reports (F2.2, F3.1 and F3.2). NOTE The term "certificate" is in common use, however for fastener inspection documents the terminology to be used is "test report". ISO 16228:2017 specifies requirements for the content of each fastener inspection document, in conjunction with the order, the relevant standards and/or specified requirements. ISO 16228:2017 is applicable to finished fasteners such as bolts, screws, studs, nuts, washers, pins, rivets, etc. made of steel, stainless steel, non-ferrous metal or non-metallic material. ISO 16228:2017 does not apply to special-purpose or specially engineered applications requiring other types of procedures (e.g. initial samples). Examples of inspection documents are given in Annex A. An example of a coding system identifying the sections in fastener inspection documents is given in Annex B.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Inspection
4.1 Types of inspection documents for material
4.2 Types of inspection for fasteners
4.3 Types of inspection documents for fasteners
5 Requirements for fastener inspection documents
5.1 General
5.2 Maintenance of data for inspection documents
5.3 Traceability
5.4 Inspection document sources
5.5 Subcontracted tests and/or inspection
5.6 Sampling
5.7 Reporting of test/inspection results
5.8 Minimum results to be included for each type of fasteners
5.9 Validation of the inspection document
6 Required content for each type of fastener inspection document
6.1 General
6.2 Content of the fastener declaration of compliance F2.1
6.3 Content of the fastener test report F2.2
6.4 Content of the fastener test report F3.1
6.5 Content of the fastener test report F3.2
7 Amendment to inspection documents
8 Transmission of inspection documents
Annex A Examples of inspection documents (informative)
Annex B Code numbers applicable to fasteners (informative)
ISO 10666:1999 Drilling screws with tapping screw thread -- Mechanical and functional properties
ISO 1891-4:2018 Fasteners -- Vocabulary -- Part 4: Control, inspection, delivery, acceptance and quality
ISO 2320:2015 Fasteners -- Prevailing torque steel nuts -- Functional properties
ISO 10666:1999 Drilling screws with tapping screw thread -- Mechanical and functional properties
ISO 1891-4:2018 Fasteners -- Vocabulary -- Part 4: Control, inspection, delivery, acceptance and quality
ISO 2320:2015 Fasteners -- Prevailing torque steel nuts -- Functional properties
ISO 2702:2011 Heat-treated steel tapping screws -- Mechanical properties
ISO 3269:2000 Fasteners -- Acceptance inspection
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 1: Bolts, screws and studs
ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 2: Nuts
ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 3: Set screws and similar fasteners not under tensile stress
ISO 3506-4:2009 Mechanical properties of corrosion-resistant stainless steel fasteners -- Part 4: Tapping screws
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes -- Coarse thread and fine pitch thread
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 2: Nuts with specified property classes -- Coarse thread and fine pitch thread
ISO 898-3:2018 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 3: Flat washers with specified property classes
ISO 898-5:2012 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 5: Set screws and similar threaded fasteners with specified hardness classes -- Coarse thread and fine pitch thread