SFS-EN ISO 11296-4:2018:en

Soveltamisala

Suomenkielistä soveltamisalaa ei ole saatavissa.

ISO 11296-4:2018, in conjunction with ISO 11296-1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks with service temperatures up to 50 °C.
ISO 11296-4:2018 applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials, reinforcement, and other process-related plastics components (see 5.3).

Tämän julkaisun valmistelusta Suomessa vastaa Muoviteollisuus ry, puh. 09 172 841 (vaihde).

Sisällysluettelo

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms

4.1 Symbols
4.2 Abbreviated terms

5 Pipes at the “M” stage

5.1 Materials
5.2 General characteristics
5.3 Material characteristics
5.4 Geometric characteristics
5.5 Mechanical characteristics
5.6 Physical characteristics
5.7 Jointing
5.8 Marking

6 Fittings at the “M” stage

6.1 Materials
6.2 General characteristics
6.3 Material characteristics
6.4 Geometric characteristics
6.5 Mechanical characteristics
6.6 Physical characteristics
6.7 Jointing
6.8 Marking

7 Ancillary components
8 Fitness for purpose of the installed lining system at the “I” stage

8.1 Materials
8.2 General characteristics
8.3 Material characteristics
8.4 Geometric characteristics
8.5 Mechanical characteristics
8.6 Physical characteristics
8.7 Additional characteristics
8.8 Sampling

9 Installation practice

9.1 Preparatory work
9.2 Storage, handling and transport of pipe components
9.3 Equipment
9.4 Installation
9.5 Process-related inspection and testing
9.6 Lining termination
9.7 Reconnections to existing pipeline system
9.8 Final inspection and testing
9.9 Documentation

Annex A CIPP components and their functions (informative)
Annex B Cured-in-place pipes — Determination of short-term flexural properties (normative)
Annex C Cured-in-place pipes — Determination of long-term flexural modulus under dry or wet conditions (normative)
Annex D Cured-in-place pipes — Determination of long-term flexural strength under dry, wet or acidic conditions (stress corrosion test) (normative)

Bibliography

Näytä kaikki

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms

4.1 Symbols
4.2 Abbreviated terms

5 Pipes at the “M” stage

5.1 Materials
5.2 General characteristics
5.3 Material characteristics
5.4 Geometric characteristics
5.5 Mechanical characteristics
5.6 Physical characteristics
5.7 Jointing
5.8 Marking

6 Fittings at the “M” stage

6.1 Materials
6.2 General characteristics
6.3 Material characteristics
6.4 Geometric characteristics
6.5 Mechanical characteristics
6.6 Physical characteristics
6.7 Jointing
6.8 Marking

7 Ancillary components
8 Fitness for purpose of the installed lining system at the “I” stage

8.1 Materials
8.2 General characteristics
8.3 Material characteristics
8.4 Geometric characteristics
8.5 Mechanical characteristics
8.6 Physical characteristics
8.7 Additional characteristics
8.8 Sampling

9 Installation practice

9.1 Preparatory work
9.2 Storage, handling and transport of pipe components
9.3 Equipment
9.4 Installation
9.5 Process-related inspection and testing
9.6 Lining termination
9.7 Reconnections to existing pipeline system
9.8 Final inspection and testing
9.9 Documentation

Annex A CIPP components and their functions (informative)
Annex B Cured-in-place pipes — Determination of short-term flexural properties (normative)
Annex C Cured-in-place pipes — Determination of long-term flexural modulus under dry or wet conditions (normative)
Annex D Cured-in-place pipes — Determination of long-term flexural strength under dry, wet or acidic conditions (stress corrosion test) (normative)

Bibliography

Tuoteryhmä(t)

23.040.20 Muoviputket »
23.040.45 Muoviset putkiyhteet »
91.140.80 Viemäröinti »
93.030 Viemäriverkostot »

Sidokset

Velvoittavat viittaukset

EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage -- Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes -- Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor

EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage -- Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes -- Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
ISO 10928:2016 Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes and fittings -- Methods for regression analysis and their use
ISO 10952:2014 Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes and fittings -- Determination of the resistance to chemical attack for the inside of a section in a deflected condition
ISO 11296-1:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks -- Part 1: General
ISO 13002:1998 Carbon fibre -- Designation system for filament yarns
ISO 14125:1998 Fibre-reinforced plastic composites -- Determination of flexural properties
ISO 14125:1998/Amd 1:2011
ISO 178:2010 Plastics -- Determination of flexural properties
ISO 178:2010/Amd 1:2013
ISO 3126:2005 Plastics piping systems -- Plastics components -- Determination of dimensions
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage -- Unplasticized poly(vinyl chloride) (PVC-U)
ISO 75-2:2013 Plastics -- Determination of temperature of deflection under load -- Part 2: Plastics and ebonite
ISO 7684:1997 Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes -- Determination of the creep factor under dry conditions
ISO 7685:1998 Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes -- Determination of initial specific ring stiffness
ISO 8513:2016 Plastics piping systems -- Glass-reinforced thermosetting plastics (GRP) pipes -- Test methods for the determination of the initial longitudinal tensile strength
ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage -- Polypropylene (PP)
ISO 899-2:2003 Plastics -- Determination of creep behaviour -- Part 2: Flexural creep by three-point loading

Tekninen komitea

CEN/TC 155 Plastics piping systems and ducting systems »

Vahvistuspäivä

23.02.2018

Julkaisupäivä

27.02.2018

Painos

2

Sivumäärä

48

Julkaisun kieli

englanti