Earth-moving and building construction machinery. Electromagnetic compatibility (EMC) of machines with internal electrical power supply. Part 2: Additional EMC requirements for functional safety (ISO 13766-2:2018)
Tuote ladattavissa hetiToimitusaika on noin 1 - 2 työpäivääToimitusaika on 3 - 5 työpäivää.
ISO 13766-2:2018 provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility (EMC) of earth-moving machinery, as defined in ISO 6165:2012, and of the following building construction machinery as classified in ISO/TR 12603:2010: - drilling and foundation equipment; - equipment used for the preparation, conveyance and compaction of concrete, mortar and processing reinforcement; - road construction and maintenance machinery and equipment. ISO 13766-2:2018 deals with EMC requirements related to the functional safety of the machinery, its electrical/electronic subassemblies (ESA) and of separate ESA. ISO 13766-2:2018 is relevant only to the safety-related parts of control systems (SRP/CS) as defined in ISO 13849-1:2015 using electrical/electronic components which meet design requirements equal to or greater than safety-related performance level PL b as defined in ISO 13849-1:2015. It also deals with electrical and electronic components or separate ESA intended to be fitted on machinery under the restriction of PL b. The following electromagnetic disturbance phenomena are evaluated: - radiated electromagnetic fields from off-board sources with various field strengths and frequencies; - radiated electromagnetic fields from on-board sources (antenna inside/outside) with various field strengths and frequencies; - electrostatic discharge; - conducted and coupled electrical transients. The machinery can have DC or AC or a combination of both as the internal electrical power supply system. ISO 13766-2:2018 is not applicable to machines that are designed to be supplied by an external mains network or to phenomena caused by military applications. NOTE Grid-connected machines are covered by IEC 61000.
Tämän julkaisun valmistelusta Suomessa vastaa Metalliteollisuuden Standardisointiyhdistys ry, puh. 09 19 231 (vaihde).
Sisällysluettelo
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 General principles
5 EMC phenomena
5.1 General
5.2 Immunity of machinery
5.3 Immunity of ESA
6 Test report
Annex A Installation and maintenance aspects (informative)
ISO 10605:2008 Road vehicles -- Test methods for electrical disturbances from electrostatic discharge
ISO 11451-2:2015 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 2: Off-vehicle radiation sources
ISO 11451-4:2013 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 4: Bulk current injection (BCI)
ISO 10605:2008 Road vehicles -- Test methods for electrical disturbances from electrostatic discharge
ISO 11451-2:2015 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 2: Off-vehicle radiation sources
ISO 11451-4:2013 Road vehicles -- Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 4: Bulk current injection (BCI)
ISO 11452-2:2004 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 2: Absorber-lined shielded enclosure
ISO 11452-3:2016 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 3: Transverse electromagnetic (TEM) cell
ISO 11452-4:2011 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 4: Harness excitation methods
ISO 11452-5:2002 Road vehicles -- Component test methods for electrical disturbances from narrowband radiated electromagnetic energy -- Part 5: Stripline
ISO 12100:2010 Safety of machinery -- General principles for design -- Risk assessment and risk reduction
ISO 13766-1:2018 Earth-moving and building construction machinery -- Electromagnetic compatibility (EMC) of machines with internal electrical power supply -- Part 1: General EMC requirements under typical electromagnetic environmental conditions
ISO 13849-1:2015 Safety of machinery -- Safety-related parts of control systems -- Part 1: General principles for design
ISO 15998:2008 Earth-moving machinery -- Machine-control systems (MCS) using electronic components -- Performance criteria and tests for functional safety
ISO 6165:2012 Earth-moving machinery -- Basic types -- Identification and terms and definitions
ISO 7637-1:2015 Road vehicles -- Electrical disturbances from conduction and coupling -- Part 1: Definitions and general considerations
ISO 7637-3:2016 Road vehicles -- Electrical disturbances from conduction and coupling -- Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
ISO/TR 12603:2010 Building construction machinery and equipment -- Classification